Fehler ID |
Fehlername |
1000 |
System error %1 |
1001 |
System error %1 |
1002 |
System error %1 |
1003 |
Alarm pointer for this self-clearing alarm %1 is zero |
1004 |
Alarm reaction to NCK alarm incorrectly configured |
1005 |
Operating system error %1 parameter %2 %3 %4 |
1010 |
Channel %1 system error %2 action %3 |
1011 |
Channel %1 %3 %4 system error %2 |
1012 |
Channel %1 system error %2 %3 %4 |
1013 |
Channel %1 system error %2 |
1014 |
Channel %1 system error %2 |
1015 |
Channel %1 axis %2 system error %3 |
1016 |
Channel %1 axis %2 system error %3 |
1017 |
Channel %1 axis %2 system error %3 |
1018 |
Floating point arithmetic error in channel %1 task %2 station %3 FPU state %4 %4 |
1019 |
Floating point arithmetic error at address %3 in channel %1 task %2 FPU state %4 |
1030 |
System error in link module error code %1 error type %2 |
1031 |
Link module generated an unspecified error %1 NCU %2 %3 %4 |
1100 |
No valid firmware |
1160 |
Assertion failed in %1: %2 |
2000 |
PLC sign-of-life monitoring |
2001 |
PLC has not started up |
2100 |
NCK battery warning threshold reached |
2101 |
NCK battery alarm |
2102 |
NCK battery alarm |
2110 |
NCK temperature alarm |
2120 |
NCK fan alarm |
2130 |
5V/24V encoder or 15V D/A converter under voltage |
2140 |
The actual service switch position forces a SRAM to be cleared at the next Power On (general reset active) |
2190 |
Hardware plug-in module for communication with the digitizer missing |
2192 |
No NCU link module exists, MD %1 reset |
2193 |
“Safety Integrated” is not available for link axis %1. |
2195 |
Channel %1 axis %2 high-speed punching/nibbling not possible via link |
2196 |
Link axis active and $MN_MM_SERVO_FIFO_SIZE != %1 |
2900 |
Reboot is delayed |
3000 |
Emergency stop |
3001 |
Internal emergency stop |
4000 |
Channel %1 machine data %2[%3] has gap in axis assignment |
4001 |
Channel %1 axis %2 defined for more than one channel via machine data %3 |
4002 |
Channel %1 machine data %2[%3] assigns an axis not defined in channel |
4003 |
Axis %1 incorrect assignment of master channel in machine data %2 |
4004 |
Channel %1 machine data %2 axis %3 defined repeatedly as geometry axis |
4005 |
Maximum number of axes in channel %1 exceeded. Limit %2 |
4007 |
Axis %1 incorrect assignment of master NCU in machine data %2 |
4010 |
Invalid identifier used in machine data %1[%2] |
4011 |
Channel %1 invalid identifier used in machine data %2[%3] |
4012 |
Invalid identifier used in machine data %1[%2] |
4013 |
Invalid NCU link configuration by machine data %1 = %2 , on NCU_1 = %3 |
4014 |
Axis %1 defined several times in %2 |
4016 |
Axis %1 already used by NCU %2 |
4017 |
Axis container %1, location %2 already used by NCU %3 |
4018 |
Axis container %1, location %2 not used by any channel |
4019 |
Axis container %1 advance not allowed with current status of NCU %2 |
4020 |
Identifier %1 used several times in machine data %2 |
4021 |
Channel %1 identifier %2 used several times in machine data %3 |
4022 |
Axis container %3 switch not allowed: ext. zero offset active channel %1 axis %2 |
4023 |
Axis container %1 switch not allowed, axis container %2 switch active |
4024 |
Invalid axis configuration due to missing axis container machine data |
4025 |
Axis container %3 switch not allowed: master/slave active channel %1 axis %2 |
4026 |
Machine data %1[%2], link axis NC%3_AX%4 not used by any channel |
4027 |
Notice: MD %1 was also changed for the other axes of axis container %2 |
4028 |
Notice! The axial MDs of the axes of the axis containers were matched. |
4029 |
Notice: the axial MDs in axis container %1 will be matched on the next power-up |
4030 |
Channel %1 axis identifier missing in machine data %2[%3] |
4031 |
Channel %1 link axis %2 defined for more than one channel in machine data %3 |
4032 |
Channel %1 wrong identifier for facing axis in %2 |
4033 |
Notice: NCU link communication still not connected |
4034 |
Local link axis %1 is not allowed for different interpolation cycle time = %2/%3 |
4035 |
Interpolation cycle from NCU%1 = %2 does not match NCU%3 = %4 |
4036 |
Wrong NCU link configuration by MD %1 |
4040 |
Channel %1 axis identifier %2 not consistent with machine data %3 |
4045 |
Channel %1 conflict between machine data %2 and machine data %3 |
4050 |
NC code identifier %1 cannot be reconfigured to %2 |
4060 |
Standard machine data loaded |
4062 |
Backup data loaded |
4065 |
Buffered memory was restored from backup medium (potential loss of data!) |
4066 |
Buffered memory of FFS restored from backup medium (potential loss of data!) |
4070 |
Normalizing machine data has been altered |
4073 |
Compile cycle functions define machine data number %1 several times |
4075 |
Machine data %1 (and maybe others) not altered due to missing permission level %2 |
4076 |
%1 Machine data could not be altered with permission level %2 |
4077 |
New value %1 of MD %2 not set. Requested %3 bytes too much %4 memory. |
4080 |
Incorrect configuration of indexing axis in MD %1 |
4090 |
Too many errors during power-up |
4100 |
System cycle time/scan time divider corrected for digital drive |
4102 |
Default values for drive cycle times differ |
4110 |
IPO factor increased to %1 |
4111 |
PLC cycle increased to %1 ms |
4112 |
Servo cycle changed to %1 ms |
4113 |
Sysclock cycle changed to %1 ms |
4114 |
Error in DP cycle of SDB1000 |
4115 |
Time ratio communication to Ipo changed to %1 |
4150 |
Channel %1 invalid M function sub program call configured |
4152 |
Illegal configuration of the “Block display with absolute values” function |
4160 |
Channel %1 invalid M function number configured for spindle switchover |
4170 |
Invalid M function number for channel synchronisation assigned |
4180 |
Invalid M function number assigned to enable ASUP |
4181 |
Channel %1 invalid assignment of an M auxiliary function number |
4182 |
Channel %1 invalid M auxiliary function number in %2%3, MD reset |
4183 |
Channel %1 M auxiliary function number %2 used several times (%3 and %4) |
4184 |
Channel %1 illegally predefined auxiliary function in %2%3, MD reset |
4185 |
Channel %1 illegal auxiliary function configured %2 %3 %4 |
4200 |
Channel %1 geometry axis %2 must not be declared a rotary axis |
4210 |
Channel %1 spindle %2 declaration as rotary axis missing |
4215 |
Channel %1 spindle %2 declaration as modulo axis missing |
4220 |
Channel %1 spindle %2 declared repeatedly |
4225 |
Channel %1 axis %2 declaration as rotary axis missing |
4230 |
Channel %1 data alteration from external not possible in current channel state |
4240 |
Runtime overflow for IPO cycle or position controller cycle, IP %1 |
4250 |
FastPlcCom functionality not available |
4252 |
PLCIO read error: %1 |
4254 |
PLCIO write error: %1 |
4260 |
Machine data %1 illegal |
4270 |
Machine data %1 assigns not activated NCK input/output byte %2 |
4275 |
Machine data %1 and %2 both assign the same NCK output byte no. %3 several times |
4280 |
Assignment of NCK input/output byte via MD %1[%2] does not match hardware configuration |
4282 |
Hardware of external NCK outputs assigned repeatedly |
4285 |
Error on terminal block %1, error code %2 |
4290 |
Local P-bus sign-of-life monitoring |
4291 |
Module in local P-bus slot %1 error codes %2 %3 %4 %2 %3 %4 |
4300 |
Declaration in MD %1 is not allowed for geometry axis/spindle %2. |
4310 |
Declaration in MD %1 index %2 is not allowed. |
4320 |
Axis %1 function %2 %3 and %4 not allowed |
4334 |
Channel %1 The amount of fine correction in parameter %2 of the orientable toolholder %3 is too large |
4336 |
Channel %1 orientable toolholder no. %2 for orientation transformation %3 does not exist |
4338 |
Channel %1 invalid transformation type ‘%2’ in toolholder %3 for orientation transformer %4 |
4340 |
Channel %1 block %2 invalid transformation type in transformation no. %3 |
4341 |
Channel %1 block %2 no data set available for transformation no. %3 |
4342 |
Channel %1 invalid machine data for general 5-axis transformation error no. %2 |
4343 |
Channel %1 attempt made to change the machine data of an active transformation. |
4345 |
Channel %1 invalid configuration in chained transformation no.%2 |
4346 |
Channel %1 invalid geoaxis assignment in machine data %2[%3] |
4347 |
Channel %1 invalid channel axis assignment in machine data %2[%3] |
4350 |
Channel %1 axis identifier %2 machine data %3 not consistent with machine data %4 |
4400 |
MD alteration will cause reorganisation of buffered memory (loss of data!) |
4502 |
Channel %1 anachronism %2(%3) -> %4 |
5000 |
Communication job not executable %1 |
6000 |
Memory reorganized using standard machine data |
6010 |
Channel %1 data block %2 not or not completely created, error code %3 |
6020 |
Machine data have been altered – now memory is reorganized |
6030 |
Limit of user memory has been adapted |
6035 |
Instead of %1 KB the system has only %2 KB of free user memory of type “%3” |
6100 |
Error while creating %1, error number %2 %3 |
6401 |
Channel %1 tool change not possible: Empty location for tool %2 Duplo no. %3 on magazine %4 not available. |
6402 |
Channel %1 tool change not possible. Magazine no. %2 not available |
6403 |
Channel %1 tool change not possible. Magazine location number %2 on magazine %3 not available. |
6404 |
Channel %1 tool change not possible. Tool %2 not available or not usable |
6405 |
Channel %1 command %2 has invalid PLC acknowledge parameter %3 – identifier %4 |
6406 |
Channel %1 PLC acknowledge for command %2 is missing |
6407 |
Channel %1 tool %2 cannot be placed in magazine %3 on location %4.Invalid definition of magazine! |
6410 |
TO unit %1 tool %2 / Duplo no. %3 has reached its pre warning limit with D = %4 |
6411 |
Channel %1 tool %2 / Duplo no. %3 has reached its prewarning limit with D = %4 |
6412 |
TO unit %1 tool %2 / Duplo no. %3 has reached its monitoring limit with D = %4 |
6413 |
Channel %1 tool %2 / Duplo no. %3 has reached its monitoring limit with D = %4 |
6421 |
Channel %1 tool move not possible. Empty location for tool %2 Duplo no. %3 on magazine %4 not available. |
6422 |
Channel %1 tool move not possible. Magazine no. %2 not available. |
6423 |
Channel %1 tool move not possible. Location %2 on magazine %3 not available. |
6424 |
Channel %1 tool move not possible. Tool %2 not available/not usable. |
6425 |
Channel %1 tool %2 cannot be placed in magazine %3 on location %4. Invalid definition of magazine! |
6430 |
Workpiece counter: overflow in table of monitored cutting edges. |
6431 |
Function not allowed. Tool management/monitoring is not active. |
6432 |
Function not executable. No tool assigned to tool holder/spindle |
6433 |
Channel %1 block %2 %3 not available with tool management |
6434 |
Channel %1 block %2 NC command SETMTH not allowed because tool holder function not active |
6441 |
Writing of $P_USEKT not allowed. |
6442 |
Channel %1 function not executable. No tool assigned to desired magazine/magazine location %2. |
6450 |
Channel %1 tool change not possible. Invalid magazine location no. %2 in buffer magazine |
6451 |
Channel %1 tool change not possible. No buffer magazine defined. |
6452 |
Channel %1 tool change not possible. Tool holder/spindle number = %2 not defined. |
6453 |
Channel %1 tool change not possible. No assignment between toolholder/spindle no. = %2 and buffer magazine location %3 |
6454 |
Channel %1 tool change not possible. No distance relation available. |
6500 |
NC memory full |
6510 |
Too many part programs in the NC memory |
6520 |
The value of the machine data %1%2 is too low |
6530 |
Too many files in directory |
6540 |
Too many directories in the NC memory |
6550 |
Too many subdirectories |
6560 |
Data format not allowed |
6570 |
NC memory full |
6580 |
NC memory full |
6600 |
NC card memory is full |
6610 |
Too many files open on NC card |
6620 |
NC card has incorrect format |
6630 |
NC card hardware is defective |
6640 |
NC card is not inserted |
6650 |
Write protection of NC card is active |
6660 |
‘Flash File System’ option is not set |
6670 |
NC card read active |
6671 |
NC card write active |
6690 |
Cycles from NC card cannot be copied to the passive file system. |
6691 |
Cycles from the passive file system cannot be saved on the NC card |
6692 |
Cycle %1 lost |
6693 |
File %1 lost |
6698 |
Unknown NC card (%1/%2). Writing not possible. |
6700 |
Channel %1 value of the machine data %2%3 is too low |
7000 |
Too many compile cycle alarms defined |
7010 |
Range of MMC alarm numbers for compile cycles exceeded |
7020 |
Compile cycle alarm number has not been defined |
7100 |
Compile cycles VDI area: %1 byte for inputs and %2 byte for outputs. Maximum %3 bytes available. |
7200 |
Problem with externally linked compile cycle %1 %2 |
7201 |
Assertion error in %1 line %2 |
7202 |
Missing option bit for %1: %2 |
8000 |
Channel %1 option ‘user interrupt programs’ not set |
8010 |
Option ‘activation of more than %1 axes’ not set |
8020 |
Option ‘activation of more than %1 channels’ not set |
8021 |
Option ‘activation of more than %1 mode groups’ not set |
8022 |
Option ‘activation of more than %1KB SRAM’ not set |
8030 |
Channel %1 block %2 option ‘interpolation of more than 4 axes’ not set |
8032 |
Option ‘activation of more than %1 link axes’ not set |
8034 |
Option ‘activation of axis containers’ not set |
8036 |
Option: it is not allowed to set different IPO cycles or position control cycles with NCU link. |
8038 |
Option ‘activation of more than %1 lead link axes’ not set |
8040 |
Machine data %1 reset, corresponding option is not set |
8041 |
Axis %1: MD %2 reset, corresponding option not sufficient |
8044 |
Option for IPO cycle time %1 ms not set |
8045 |
Option for selected cycle settings not set |
8080 |
%1 options are activated without setting the license key |
8081 |
%1 options are activated that are not licensed by the license key |
8082 |
The license key was entered three times, Power On required before next try. |
8098 |
Invalid combination of options (%1) |
8100 |
Channel %1 block %2: function not possible |
10203 |
Channel %1 NC start without reference point |
10207 |
Channel %1 error when selecting or deselecting the digitize function |
10208 |
Channel %1 continue program with NC start |
10209 |
Channel %1 internal NC stop after block search |
10222 |
Channel %1 inter-channel communication not possible |
10223 |
Channel %1: Command %2 is already occupied |
10225 |
Channel %1: command denied |
10299 |
Channel %1 Auto-Repos function is not enabled |
10600 |
Channel %1 block %2 auxiliary function during thread cutting active |
10601 |
Channel %1 block %2 zero velocity at block end point during thread cutting |
10604 |
Channel %1 block %2 thread lead increase too high |
10605 |
Channel %1 block %2 thread lead decrease too high |
10607 |
Channel %1 block %2 thread with frame not executable |
10610 |
Channel %1 axis %2 not stopped |
10620 |
Channel %1 block %3 axis %2 at software limit switch %4 |
10621 |
Channel %1 axis %2 rests on software limit switch %3 |
10630 |
Channel %1 block %2 axis %3 at working area limit %4 |
10631 |
Channel %1 axis %2 rests at working area limit %3 |
10650 |
Channel %1 axis %2 incorrect gantry machine data, error code %3 |
10651 |
Channel %1 illegal gantry configuration. Error code %2 |
10652 |
Channel %1 axis %2 gantry warning threshold exceeded |
10653 |
Channel %1 axis %2 gantry error threshold exceeded |
10654 |
Channel %1 waiting for synchronization start of gantry group %2 |
10655 |
Channel %1 synchronization of gantry group %2 in progress |
10656 |
Channel %1 axis %2 gantry alarm not yet used |
10700 |
Channel %1 block %2 NCK protection zone %3 violated during automatic or MDA mode |
10701 |
Channel %1 block %2 channel-specific protection zone %3 violated during automatic or MDA mode |
10702 |
Channel %1 NCK protection zone %2 violated during manual mode |
10703 |
Channel %1 channel-specific protection zone %2 violated during manual mode |
10704 |
Channel %1 block %2 protection zone monitoring is not guaranteed |
10706 |
Channel %1 NCK protection zone %2 reached with axis %3 during manual mode |
10707 |
Channel %1 channel-specific protection zone %2 reached with axis %3 during manual mode |
10710 |
Channel %1 block %2 conflict with centre less grinding |
10720 |
Channel %1 block %3 axis %2 software limit switch %4 |
10721 |
Channel %1 block %3 axis %2 software limit switch %4 |
10730 |
Channel %1 block %3 axis %2 working area limitation %4 |
10731 |
Channel %1 block %3 axis %2 working area limitation %4 |
10740 |
Channel %1 block %2 too many empty blocks in WAB programming |
10741 |
Channel %1 block %2 direction reversal with WAB infeed motion |
10742 |
Channel %1 block %2 WAB distance invalid or not programmed |
10743 |
Channel %1 block %2 WAB programmed several times |
10744 |
Channel %1 block %2 no valid WAB direction defined |
10745 |
Channel %1 block %2 WAB end position not clear |
10746 |
Channel %1 block %2 block search stop for WAB |
10747 |
Channel %1 block %2 retraction direction not defined for WAB |
10748 |
Channel %1 block %2 illegal retract plane with WAB |
10750 |
Channel %1 block %2 tool radius compensation activated without tool number |
10751 |
Channel %1 block %2 danger of collision due to tool radius compensation |
10752 |
Channel %1 block %2 overflow of local block buffer with tool radius compensation |
10753 |
Channel %1 block %2 selection of the tool radius compensation only possible in linear block |
10754 |
Channel %1 block %2 deselection of the tool radius compensation only possible in linear block |
10755 |
Channel %1 block %2 selection of the tool radius compensation via KONT not possible at the current starting point |
10756 |
Channel %1 block %2 deselection of the tool radius compensation via KONT not possible at the programmed end point |
10757 |
Channel %1 block %2 changing the compensation plane while tool radius compensation is active not possible |
10758 |
Channel %1 block %2 curvature radius with variable compensation value too small |
10759 |
Channel %1 block %2 path is parallel to tool orientation |
10760 |
Channel %1 block %2 helical axis is not parallel to tool orientation |
10761 |
Channel %1 block %2 tool radius compensation for ellipse with more than one revolution not possible |
10762 |
Channel %1 block %2 too many empty blocks between two traversing blocks with active tool radius compensation |
10763 |
Channel %1 block %2 path component of the block in the compensation plane becomes zero |
10764 |
Channel %1 block %2 discontinuous path with active tool radius compensation |
10765 |
Channel %1 block %2 3D tool radius compensation not possible |
10766 |
Channel %1 illegal change of surface orientation between block %2 and block %3 |
10767 |
Channel %1 block %2 processing with tilt angle unequal 0 not possible |
10768 |
Channel %1 block %2 illegal tool orientation with 3D tool radius compensation |
10769 |
Channel %1 block %2 Illegal surface normal vector with 3D tool radius compensation |
10770 |
Channel %1 block %2 change of corner type due to change of orientation with active tool radius compensation |
10771 |
Channel %1 block %2 overflow of local block buffer due to orientation smoothing |
10772 |
Channel %1 block %2 illegal orientation change when activating or deactivating 3D face cutting |
10773 |
Channel %1 illegal tool orientation in block %2 at inside corner with block %3 |
10774 |
Channel %1 illegal tool dimensions with face cutting in block %2 |
10775 |
Channel %1 illegal tool change with face cutting in block %2 |
10776 |
Channel %1 block%2 axis %3 must be geometry axis if tool radius compensation is active |
10777 |
Channel %1 block %2 tool radius compensation: too many blocks with suppression of compensation |
10778 |
Channel %1 block %2 preprocessing stop with active tool radius compensation |
10779 |
Channel %1 block %2 preprocessing stop with active tool radius compensation |
10780 |
Channel %1 block %2 preprocessing stop with active tool radius compensation |
10781 |
Channel %1 block %2 illegal orientation of involute with tool radius compensation |
10782 |
Channel %1 block %2 illegal curve type with tool radius compensation |
10783 |
Channel %1 block %2 tool radius compensation type requires orientation transformation |
10784 |
Channel %1 block %2 illegal tool for tool radius compensation with constraint surface |
10790 |
Channel %1 block %2 plane change during linear programming with angles |
10791 |
Channel %1 block %2 invalid angle during linear programming |
10792 |
Channel %1 block %2 illegal interpolation type during linear programming with angles |
10793 |
Channel %1 block %2 second block missing during linear programming with angles |
10794 |
Channel %1 block %2 angle specification missing in second block during linear interpolation with angles |
10795 |
Channel %1 block %2 end point specification during angle programming contradictory |
10800 |
Channel %1 block %3 axis %2 is not a geometry axis |
10805 |
Channel %1 block %2 repositioning after switch of geometry axes or transformation |
10810 |
Channel %1 block %2 master spindle not defined |
10820 |
Channel %1 rotary axis/spindle %2 not defined |
10860 |
Channel %1 block %2 feedrate not programmed |
10861 |
Channel %1 block %3 velocity of positioning axis %2 is zero |
10862 |
Channel %1 block %2 master spindle also used as path axis |
10870 |
Channel %1 block %2 facing axis not defined |
10880 |
Channel %1 block %2 too many empty blocks between two traversing blocks when inserting chamfers or radii |
10881 |
Channel %1 block %2 overflow of local block buffer when inserting chamfers or radii |
10882 |
Channel %1 block %2 activation of chamfers or radii (non-modal) without traversing movement in the block |
10883 |
Channel %1 block %2 chamfer or fillet has to be reduced |
10890 |
Channel %1 block %2 overflow of local block buffer when calculating splines |
10891 |
Channel %1 block %2 multiplicity of node is greater than its order |
10900 |
Channel %1 block %2 no S value programmed for constant cutting speed |
10910 |
Channel %1 block %2 excessive velocity of one path axis |
10911 |
Channel %1 block %2 transformation prohibits to traverse the pole |
10912 |
Channel %1 block %2 preprocessing and main run might not be synchronized |
10913 |
Channel %1 block %2 negative feed profile is ignored |
10914 |
Movement not possible while transformation active – in channel %1, block %2 |
10930 |
Channel %1 block %2 interpolation type not allowed in stock removal contour |
10931 |
Channel %1 block %2 incorrect stock removal contour |
10932 |
Channel %1 block %2 preparation of contour has been restarted |
10933 |
Channel %1 block %2 contour program does not contain enough contour blocks |
10934 |
Channel %1 block %2 array for contour segmentation is set too small |
10940 |
Channel %1 block %2 curve table %3: delete/overwrite not possible |
10941 |
Channel %1 block %2 curve table %3: NC memory full |
10942 |
Channel %1 block %2 curve table %3: illegal instruction during definition |
10943 |
Channel %1 block %2 curve table %3: direction reversal of lead value in the block not allowed |
10944 |
Channel %1 block %2 curve table %3: illegal transformation |
10945 |
Channel %1 block %2 curve table %3: illegal coupling of axes |
10946 |
Channel %1 block %2 curve table %3: no contour defined |
10947 |
Channel %1 block %2 curve table %3: contour not continuous |
10948 |
Channel %1 block %2 curve table %3: position jump at end of period |
10949 |
Channel %1 block %2 curve table %3: missing master axis motion |
10950 |
Channel %1 calculation of arc length function too inaccurate |
10951 |
Channel %1 block %2 curve table %3: following value period is zero |
10955 |
Channel %1 block %2 curve table %3: missing master axis motion |
10956 |
Channel %1 block %2 curve table %3: NC memory limit DRAM reached |
10960 |
Channel %1 block %2 COMPCURV/COMPCAD and radius compensation cannot be used simultaneously |
10961 |
Channel %1 block %2 maximum cubic polynomials are allowed on active radius compensation. |
10962 |
Channel %1 block %2 function %3 not possible with path correction |
12000 |
Channel %1 block %2 address %3 programmed repeatedly |
12010 |
Channel %1 block %2 address %3 address type programmed too often |
12020 |
Channel %1 block %2 illegal address modification |
12030 |
Channel %1 block %2 invalid parameter or data type in %3 |
12040 |
Channel %1 block %2 expression %3 is not of data type ‘AXIS’ |
12050 |
Channel %1 block %2 DIN address %3 not configured |
12060 |
Channel %1 block %2 same G group programmed repeatedly |
12070 |
Channel %1 block %2 too many syntax-defining G functions |
12080 |
Channel %1 block %2 syntax error in text %3 |
12090 |
Channel %1 block %2 unexpected parameter %3 |
12100 |
Channel %1 block %2 number of passes %3 not permissible |
12110 |
Channel %1 block %2 block syntax cannot be interpreted |
12120 |
Channel %1 block %2 G function not separately programmed |
12130 |
Channel %1 block %2 illegal tool orientation |
12140 |
Channel %1 block %2 functionality %3 not implemented |
12150 |
Channel %1 block %2 operation %3 not compatible with data type |
12160 |
Channel %1 block %2 range of values exceeded |
12170 |
Channel %1 block %2 identifier %3 defined repeatedly |
12180 |
Channel %1 block %2 illegal chaining of operators %3 |
12190 |
Channel %1 block %2 variable of type ARRAY has too many dimensions |
12200 |
Channel %1 block %2 symbol %3 cannot be created |
12210 |
Channel %1 block %2 string %3 too long |
12220 |
Channel %1 block %2 binary constant %3 in string too long |
12230 |
Channel %1 block %2 hexadecimal constant %3 in string too long |
12240 |
Channel %1 block %2 tool orientation %3 defined repeatedly |
12250 |
Channel %1 block %2 nested macro %3 not possible |
12260 |
Channel %1 block %2 too many initialization values specified %3 |
12261 |
Channel %1 block %2 initialization of %3 not allowed |
12270 |
Channel %1 block %2 macro identifier %3 already defined |
12280 |
Channel %1 block %2 maximum macro length %3 exceeded |
12290 |
Channel %1 block %2 arithmetic variable % 3 not defined |
12300 |
Channel %1 block %2 call-by-reference parameter missing on subroutine call %3 |
12310 |
Channel %1 block %2 axis parameter missing on procedure call %3 |
12320 |
Channel %1 block %2 parameter %3 is no variable |
12330 |
Channel %1 block %2 type of parameter %3 incorrect |
12340 |
Channel %1 block %2 number of parameters too high %3 |
12350 |
Channel %1 block %2 parameter %3 no longer possible |
12360 |
Channel %1 block %2 dimension of parameter %3 incorrect |
12370 |
Channel %1 block %2 range of values %3 not permissible |
12380 |
Channel %1 block %2 maximum memory capacity reached |
12390 |
Channel %1 block %2 initialization value %3 cannot be converted |
12400 |
Channel %1 block %2 field %3 element does not exist |
12410 |
Channel %1 block %2 incorrect index type for %3 |
12420 |
Channel %1 block %2 identifier %3 too long |
12430 |
Channel %1 block %2 specified index is invalid |
12440 |
Channel %1 block %2 maximum number of formal arguments exceeded |
12450 |
Channel %1 block %2 label defined twice |
12460 |
Channel %1 block %2 maximum number of symbols exceeded with %3 |
12470 |
Channel %1 block %2 G function %3 is unknown |
12475 |
Channel %1 block %2 invalid G function number %3 programmed |
12480 |
Channel %1 block %2 subroutine %3 already defined |
12490 |
Channel %1 block %2 access permission level %3 is not valid |
12500 |
Channel %1 block %2 in this module %3 is not possible |
12510 |
Channel %1 block %2 too many machine data %3 |
12520 |
Channel %1 block %2 too many tool parameters %3 |
12530 |
Channel %1 block %2 invalid index for %3 |
12540 |
Channel %1 block %2 Block is too long or too complex |
12550 |
Channel %1 block %2 name %3 not defined or option not installed |
12552 |
Channel %1 block %2 tool/magazine OEM parameter not defined. Option not set.Option not set. |
12560 |
Channel %1 block %2 programmed value %3 exceeds allowed limits |
12570 |
Channel %1 block %2 too many motion synchronous actions in %3 |
12571 |
Channel %1 block %2 %3 not permissible for motion synchronous action |
12572 |
Channel %1 block %2 %3 only permissible for motion synchronous action |
12580 |
Channel %1 block %2 %3 not permissible for assignment in motion synchronous action |
12581 |
Channel %1 block %2 invalid read access to %3 while in motion synchronous action |
12582 |
Channel %1 block %2 field index %3 incorrect |
12583 |
Channel %1 block %2 variable %3 no system variable |
12584 |
Channel %1 block %2 variable %3 cannot be read synchronously with motion |
12585 |
Channel %1 block %2 variable %3 cannot be changed synchronously with motion |
12586 |
Channel %1 block %2 motion synchronous action: type conflict in variable %3 |
12587 |
Channel %1 block %2 motion synchronous action: operation/function %3 not allowed |
12588 |
Channel %1 block %2 motion synchronous action: address %3 not allowed |
12589 |
Channel %1 block %2 motion synchronous action: variable %3 not allowed with modal ID |
12590 |
Channel %1 block %2 global user data cannot be created |
12600 |
Channel %1 block %2 invalid line checksum |
12610 |
Channel %1 block %2 accessing single character with call-by-reference parameter not possible %3 |
12620 |
Channel %1 block %2 accessing this variable as single character not possible |
12630 |
Channel %1 block %2 skip ID/label in control structure not allowed |
12640 |
Channel %1 block %2 invalid nesting of control structures |
12641 |
Channel %1 block %2 maximum nesting depth of control structures exceeded |
12650 |
Channel %1 block %2 axis identifier %3 different in channel %4 |
12660 |
Channel %1 block %2 motion synchronous action: variable %3 reserved for motion synchronous actions and technology cycles |
12661 |
Channel %1 block %2 technology cycle %3: no further subprogram call possible |
12700 |
Channel %1 block %2 contour definition programming not allowed as modal sub program is active |
12701 |
Channel %1 block %2 illegal interpolation type for contour definition active |
12710 |
Channel %1 block %2 illegal language element in external language mode |
12720 |
Channel %1 block %2 program number for macro call (G65/G66) missing |
12722 |
Channel %1 block %2 multiple ISO_2/3 macro or cycle calls in the block |
12724 |
Channel %1 block %2 no radius programmed for cylinder interpolation activation/deactivation |
12726 |
Channel %1 block %2 illegal plane selection with parallel axes |
12728 |
Channel %1 block %2 distance for double turret not set |
12730 |
Channel %1 block %2 no valid transformation machine data parametrized |
12740 |
Channel %1 block %2 modal macro call %3 not possible |
14000 |
Channel %1 block %2 illegal end of file |
14001 |
Channel %1 block %2 illegal end of block |
14009 |
Channel %1 block %2 illegal program path %3 |
14010 |
Channel %1 block %2 invalid default parameter in subroutine call |
14011 |
Channel %1 block %2 program %3 not existing or will be edited |
14012 |
Channel %1 block %2 maximum subroutine level exceeded |
14013 |
Channel %1 block %2 number of subroutine passes invalid |
14014 |
Channel %1 selected program %3 not available or will be edited |
14015 |
Channel %1 block %2 program %3 is not enabled |
14016 |
Channel %1 block %2 error when calling the subroutine via M/T function |
14017 |
Channel %1 block %2 syntax error when calling the subroutine via M function |
14020 |
Channel %1 block %2 wrong value or wrong number of parameters on function or procedure call |
14021 |
Channel %1 block %2 wrong value or wrong number of parameters on function or procedure call |
14025 |
Channel %1 block %2 motion synchronous action: illegal modal ID |
14026 |
Channel %1 block %2 motion synchronous action: invalid polynomial number in the FCTDEF command |
14030 |
Channel %1 block %2 combine OSCILL and POSP during oscillation with in feed motion |
14033 |
Channel %1 block %2 involute: no end point programmed |
14034 |
Channel %1 block %2 involute: angle of rotation too large |
14035 |
Channel %1 block %2 involute: start point invalid |
14036 |
Channel %1 block %2 involute: end point invalid |
14037 |
Channel %1 block %2 involute: radius invalid |
14038 |
Channel %1 block %2 involute not definable: end point error |
14039 |
Channel %1 block %2 involute: end point programmed several times |
14040 |
Channel %1 block %2 error in end point of circle |
14045 |
Channel %1 block %2 error in tangential circle programming |
14048 |
Channel %1 block %2 wrong number of revolutions in circle programming |
14050 |
Channel %1 block %2 nesting depth for arithmetic operations exceeded |
14051 |
Channel %1 block %2 arithmetic error in part program |
14060 |
Channel %1 block %2 invalid skip level with differential block skip |
14070 |
Channel %1 block %2 memory for variables not sufficient for subroutine call |
14080 |
Channel %1 block %2 jump destination %3 not found |
14082 |
Channel %1 block %2 label %3 program section not found |
14085 |
Channel %1 block %2 instruction not allowed |
14088 |
Channel %1 block %2 axis %3 doubtful position |
14090 |
Channel %1 block %2 illegal D number |
14091 |
Channel %1 block %2 illegal function, index %3 %3 |
14092 |
Channel %1 block %2 axis %3 is wrong axis type |
14093 |
Channel %1 block %2 path interval |
14094 |
Channel %1 block %2 polynominal degree greater than 3 programmed for polynominal interpolation |
14095 |
Channel %1 block %2 radius for circle programming too small |
14096 |
Channel %1 block %2 illegal type conversion |
14097 |
Channel %1 block %2 string cannot be converted to AXIS type |
14098 |
Channel %1 block %2 conversion error: no valid number found |
14099 |
Channel %1 block %2 result in string concatenation too long |
14100 |
Channel %1 block %2 orientation transformation not available |
14101 |
Channel %1 block %2 orientation transformation not active |
14102 |
Channel %1 block %2 polynominal degree greater than 5 programmed for orientation vector angle |
14110 |
Channel %1 block %2 Euler angles and orientation vector components programmed |
14111 |
Channel %1 block %2 Euler angles, orientation vector and transformation axes programmed |
14112 |
Channel %1 block %2 programmed orientation path not possible |
14113 |
Channel %1 block %2 programmed lead angle too large |
14114 |
Channel %1 block %2 programmed tilt angle too large |
14115 |
Channel %1 block %2 illegal definition of workpiece surface |
14116 |
Channel %1 block %2 absolute orientation programmed while ORIPATH is active |
14117 |
Channel %1 block %2 no angle or direction of the cone programmed |
14118 |
Channel %1 block %2 no end orientation programmed |
14119 |
Channel %1 block %2 no intermediate orientation programmed |
14120 |
Channel %1 block %2 plane determination for programmed orientation not possible |
14122 |
Channel %1 block %2 angle and direction of the cone programmed |
14123 |
Channel %1 block %2 nutation angle of the cone too small |
14124 |
Channel %1 block %2 start tangent for orientation is zero |
14125 |
Channel %1 block %2 programmed rotation is not possible |
14129 |
Channel %1 block %2 orientation angles and orientation vector components programmed |
14130 |
Channel %1 block %2 too many initialization values given |
14131 |
Channel %1 block %2 orientation axes and lead/tilt angles programmed |
14132 |
Channel %1 block %2 orientation axes incorrectly configured |
14133 |
Channel %1 block %2 G code for orientation definition not allowed |
14134 |
Channel %1 block %2 G code for orientation interpolation not allowed |
14140 |
Channel %1 block %2 position programming without transformation not allowed |
14144 |
Channel %1 block %2 PTP movement not allowed |
14146 |
Channel %1 block %2 CP or PTP movement without transformation not allowed |
14148 |
Channel %1 illegal reference system for Cartesian manual traverse |
14150 |
Channel %1 block %2 illegal tool carrier number programmed or declared (MD) |
14151 |
Channel %1 block %2 illegal tool carrier rotation |
14152 |
Channel %1 block %2 tool carrier: invalid orientation. Error code: %3 |
14153 |
Channel %1 block %2 unknown tool carrier type: %3 |
14154 |
Channel %1 block %2 The amount of fine correction in parameter %3 of the orientable tool holder %4 is too large |
14155 |
Channel %1 block %2 invalid base frame definition for tool carrier offset |
14156 |
Channel %1 toolholder selection error at reset |
14157 |
Channel %1 block %2 illegal interpolation type with MOVT |
14159 |
Channel %1 block %2 more than two angles programmed with ROTS or AROTS |
14160 |
Channel %1 block %2 tool length selection without geometry axis specification |
14165 |
Channel %1 block %2 active T number does not match selected tool |
14170 |
Channel %1 block %2 illegal interpolation type with tool length compensation |
14180 |
Channel %1 block %2 H number is not defined |
14185 |
Channel %1 block %2 D number is not defined |
14190 |
Channel %1 block %2 H number with G49 |
14195 |
Channel %1 block %2 D number with G49 |
14197 |
Channel %1 block %2 D number and H number programmed simultaneously |
14198 |
Channel %1 block %2 illegal change of tool direction with tool offset |
14199 |
Channel %1 block %2 illegal plane change for tool with diameter component |
14200 |
Channel %1 block %2 negative polar radius |
14210 |
Channel %1 block %2 polar angle too large |
14250 |
Channel %1 block %2 negative pole radius |
14260 |
Channel %1 block %2 pole angle too large |
14270 |
Channel %1 block %2 pole programmed incorrectly |
14280 |
Channel %1 block %2 polar coordinates programmed incorrectly |
14290 |
Channel %1 block %2 poly nominal degree greater than 5 programmed for poly nominal interpolation |
14300 |
Channel %1 block %2 overlaid handwheel motion activated incorrectly |
14310 |
Handwheel %1 configuration incorrect or inactive |
14400 |
Channel %1 block %2 tool radius compensation active at transformation switchover |
14401 |
Channel %1 block %2 transformation not available |
14402 |
Channel %1 block %2 spline active at transformation change |
14403 |
Channel %1 block %2 preprocessing and main run might not be synchronized |
14404 |
Channel %1 block %2 illegal parametrization of transformation |
14410 |
Channel %1 block %2 spline active at geometry axis changeover |
14411 |
Channel %1 block %2 tool radius compensation active at geometry axis changeover |
14412 |
Channel %1 block %2 transformation active at geometry axis changeover |
14413 |
Channel %1 block %2 fine tool correction: changeover geometry/channel axis not allowed |
14414 |
Channel %1 block %2 GEOAX function: incorrect call |
14415 |
Channel %1 block %2 tangent control: changeover geometry/channel axis not allowed |
14420 |
Channel %1 block %2 index axis %3 frame not allowed |
14500 |
Channel %1 block %2 illegal DEF or PROC instruction in the part program |
14510 |
Channel %1 block %2 PROC instruction missing on subroutine call |
14520 |
Channel %1 block %2 illegal PROC instruction in data definition section |
14530 |
Channel %1 block %2 EXTERN and PROC instruction do not correspond |
14600 |
Channel %1 block %2 reload buffer %3 cannot be established |
14601 |
Channel %1 block %2 reload buffer could not be deleted |
14602 |
Channel %1 block %2 timeout during EXTCALL |
14610 |
Channel %1 block %2 compensation block not possible |
14650 |
Channel %1 block %2 SETINT instruction with invalid ASUP input |
14660 |
Channel %1 block %2 SETINT instruction with invalid priority |
14700 |
Channel %1 block %2 timeout during command to interpreter |
14701 |
Channel %1 block %2 number of available NC blocks reduced by %3 |
14710 |
Channel %1 block %2 error in initialization sequence in function %3 |
14720 |
Channel %1 block %2 axes for centerless transformation not available |
14730 |
Channel %1 block %2 conflict at activation of centerless transformation |
14740 |
Channel %1 block %2 no tool data available for centerless grinding |
14745 |
Channel %1 block %2 centerless grinding not active |
14750 |
Channel %1 block %2 too many auxiliary functions programmed |
14751 |
Channel %1 block %2 resources for motion synchronous actions not sufficient (code: %3) |
14752 |
Channel %1 block %2 DELDTG | STOPREOF conflict |
14753 |
Channel %1 block %2 motion synchronous actions with illegal interpolation type |
14754 |
Channel %1 block %2 motion synchronous actions and wrong feed type |
14755 |
Channel %1 block %2 motion synchronous actions without traverse motion |
14756 |
Channel %1 block %2 motion synchronous action and wrong value |
14757 |
Channel %1 block %2 motion synchronous action and wrong type |
14758 |
Channel %1 block %2 programmed value not available |
14759 |
Channel %1 block %2 motion synchronous action and wrong axis type |
14760 |
Channel %1 block %2 auxiliary function of a group programmed repeatedly |
14761 |
Channel %1 block %2 motion synchronous action: DELDTG function not allowed with active tool radius compensation |
14762 |
Channel %1 block %2 too many PLC variables programmed |
14763 |
Channel %1 block %2 too many link variables programmed |
14764 |
NCU link cannot transfer all link variables immediately |
14765 |
NCU link cannot transfer all link variables |
14766 |
NCU link is heavily loaded, impending memory shortage |
14767 |
Machine data matching via NCU link not complete |
14770 |
Channel %1 block %2 auxiliary function programmed incorrectly |
14780 |
Channel %1 block %2 unreleased option used |
14790 |
Channel %1 block %2 axis %3 programmed by PLC |
14800 |
Channel %1 block %2 programmed path speed less or equal to zero |
14810 |
Channel %1 block %2 negative axis speed programmed for positioning axis %3 |
14811 |
Channel %1 block %2 incorrect value range for acceleration of axis/spindle %3 |
14812 |
Channel %1 block %2 SOFTA not available for axis %3 |
14815 |
Channel %1 block %2 negative thread lead change programmed |
14820 |
Channel %1 block %2 negative value for maximum spindle speed programmed with constant cutting speed |
14821 |
Channel %1 block %2 error in selection or deselection of GWPS |
14822 |
Channel %1 block %2 incorrect programming of GWPS |
14823 |
Channel %1 block %2 error on selection or deselection of tool monitoring |
14824 |
Channel %1 block %2 conflict with GWPS |
14840 |
Channel %1 block %2 incorrect value range for constant cutting speed |
14900 |
Channel %1 block %2 center point and end point programmed simultaneously |
14910 |
Channel %1 block %2 invalid angle of aperture for programmed circle |
14920 |
Channel %1 block %2 intermediate point of circle incorrect |
15000 |
Channel %1 block %2 channel-sync instruction using illegal mark |
15010 |
Channel %1 block %2 program coordination instruction with invalid channel number |
15020 |
Channel %1 block %2 CHANDATA instruction cannot be executed. Channel %3 is not active |
15021 |
Channel %1 block %2 CHANDATA instruction with invalid channel number |
15025 |
CHANDATA(%2): channel is not active. Channel data will be ignored. |
15030 |
Channel %1 block %2 different measurement system settings |
15100 |
Channel %1 block %2 REORG abort caused by log file overflow |
15110 |
Channel %1 block %2 REORG not possible |
15150 |
Channel %1 block %2 reload from external aborted |
15160 |
Channel %1 block %2 wrong preprocessing configuration |
15165 |
Channel %1 block %2 error when translating or interpreting PLC Asup %3 |
15166 |
Channel %1 user system asup _N_ASUP_SPF not available |
15170 |
Channel %1 block %2 program %3 could not be compiled |
15171 |
Channel %1 block %2 compiled program %3 older than the relevant subroutine |
15175 |
Channel %1 block %2 program %3. Interfaces could not be built |
15180 |
Channel %1 block %2 program %3 cannot be executed as INI file |
15185 |
Channel %1 %2 errors in INI file |
15190 |
Channel %1 block %2 not enough free memory for subroutine call |
15300 |
Channel %1 block %2 invalid number-of-passed-blocks during block search |
15310 |
Channel %1 block %2 file requested during block search is not available |
15320 |
Channel %1 block %2 invalid block search command |
15330 |
Channel %1 block %2 invalid block number as search target |
15340 |
Channel %1 block %2 invalid label as search target |
15350 |
Channel %1 block %2 search target not found |
15360 |
Channel %1 illegal target of block search (syntax error) |
15370 |
Channel %1 target of block search not found |
15380 |
Channel %1 block %2 illegal incremental programming in axis %3 |
15390 |
Channel %1 block %2 %3 not executed during block search |
15395 |
Channel %1 master-slave not executable during block search |
15400 |
Channel %1 block %2 selected initial init file does not exist |
15410 |
Channel %1 block %2 initialization file contains invalid M function |
15420 |
Channel %1 block %2 instruction in current mode not allowed |
15450 |
Channel %1 block %2 compiled program cannot be stored |
15460 |
Channel %1 block %2 syntax error with modal function |
15500 |
Channel %1 block %2 illegal angle of shear |
15700 |
Channel %1 block %2 illegal cycle alarm number %3 |
15800 |
Channel %1 block %2 wrong starting conditions for CONTPRON/CONTDCON |
15810 |
Channel %1 block %2 wrong array dimension for CONTPRON/CONTDCON |
15900 |
Channel %1 block %2 touch probe not allowed |
15910 |
Channel %1 block %2 touch probe not allowed |
15950 |
Channel %1 block %2 no traverse motion programmed |
15960 |
Channel %1 block %2 no traverse motion programmed |
16000 |
Channel %1 block %2 invalid value for lifting direction |
16005 |
Channel %1 block %2 invalid value for lifting distance |
16010 |
Channel %1 block %2 machining stop after lift fast |
16015 |
Channel %1 block %2 wrong axis identifier %3 |
16016 |
Channel %1 block %2 no retraction position programmed for axis %3 |
16020 |
Channel %1 repositioning in block %2 is not possible |
16100 |
Channel %1 block %2 spindle %3 not available in the channel |
16105 |
Channel %1 block %2 spindle %3 cannot be assigned |
16110 |
Channel %1 block %2 spindle %3 for dwell time not in control mode |
16120 |
Channel %1 block %2 invalid index for tool fine compensation |
16130 |
Channel %1 block %2 instruction not allowed with FTOCON |
16140 |
Channel %1 block %2 FTOCON not allowed |
16150 |
Channel %1 block %2 invalid spindle number with PUTFTOCF |
16200 |
Channel %1 block %2 spline and polynominal interpolation not available |
16300 |
Channel %1 block %2 denominator polynominal with zero places within parameter range not allowed |
16400 |
Channel %1 block %2 positioning axis %3 cannot participate in spline |
16410 |
Channel %1 block %2 axis %3 is not a geometry axis |
16420 |
Channel %1 block %2 axis %3 programmed repeatedly |
16421 |
Channel %1 block %2 angle %3 programmed repeatedly in the block |
16422 |
Channel %1 block %2 angle %3 programmed repeatedly in the block |
16423 |
Channel %1 block %2 angle %3 programmed repeatedly in the block |
16424 |
Channel %1 block %2 coordinate %3 programmed repeatedly in the block |
16430 |
Channel %1 block %2 geometry axis %3 cannot traverse as positioning axis in rotated coordinate system |
16440 |
Channel %1 block %2 rotation programmed for non-existent geometry axis |
16500 |
Channel %1 block %2 chamfer or rounding negative |
16510 |
Channel %1 block %2 no facing axis available |
16700 |
Channel %1 block %2 axis %3 invalid feed type |
16710 |
Channel %1 block %2 axis %3 master spindle not programmed |
16715 |
Channel %1 block %2 axis %3 spindle not in standstill |
16720 |
Channel %1 block %2 axis %3 thread lead is zero |
16730 |
Channel %1 block %2 axis %3 wrong parameter |
16740 |
Channel %1 block %2 no geometry axis programmed |
16750 |
Channel %1 block %2 axis %3 SPCON not programmed |
16751 |
Channel %1 block %2 spindle/axis %3 SPCOF not executable |
16755 |
Channel %1 block %2 no stop required |
16760 |
Channel %1 block %2 axis %3 S value missing |
16761 |
Channel %1 block %2 axis/spindle %3 not programmable in the channel |
16762 |
Channel %1 block %2 spindle %3 thread function is active |
16763 |
Channel %1 block %2 axis %3 programmed speed is illegal (zero or negative) |
16770 |
Channel %1 block %2 axis %3 no measuring system available |
16771 |
Channel %1 following axis %2 overlaid movement not enabled |
16776 |
Channel %1 block %2 curve table %3 does not exist for axis %4 |
16777 |
Channel %1 block %2 coupling: following axis %3 for lead axis %4 not available |
16778 |
Channel %1 block %2 coupling: Ring coupling at following axis %3 and leading axis %4 impermissible |
16779 |
Channel %1 block %2 coupling: too many couplings for axis %3, see active leading axis %4 |
16780 |
Channel %1 block %2 following spindle/axis missing |
16781 |
Channel %1 block %2 master spindle/axis missing |
16782 |
Channel %1 block %2 following spindle/axis %3 not available |
16783 |
Channel %1 block %2 master spindle/axis %3 not available |
16785 |
Channel %1 block %2 identical spindles/axes %3 |
16787 |
Channel %1 block %2 coupling parameter not changeable |
16788 |
Channel %1 block %2 cyclic coupling |
16789 |
Channel %1 block %2 multiple link |
16790 |
Channel %1 block %2 Parameter is zero or missing |
16791 |
Channel %1 block %2 parameter is not relevant |
16792 |
Channel %1 block %2 too many couplings for axis/spindle %3 |
16793 |
Channel %1 block %2 coupling of axis %3 prohibits transformation change |
16794 |
Channel %1 block %2 coupling of axis/spindle %3 prohibits reference point approach |
16795 |
Channel %1 block %2 string cannot be interpreted |
16796 |
Channel %1 block %2 coupling not defined |
16797 |
Channel %1 block %2 coupling is active |
16798 |
Channel %1 block %2 axis %3 is following axis and prohibits axis container rotation |
16799 |
Channel %1 block %2 axis %3 is master axis and prohibits axis container rotation |
16800 |
Channel %1 block %2 traverse instruction DC/CDC for axis %3 not allowed |
16810 |
Channel %1 block %2 traverse instruction ACP for axis %3 not allowed |
16820 |
Channel %1 block %2 traverse instruction ACN for axis %3 not allowed |
16830 |
Channel %1 block %2 incorrect position programmed for axis/spindle %3 |
16903 |
Channel %1 program control: action %2 not allowed in the current state |
16904 |
Channel %1 program control: action %2 not allowed in the current state |
16905 |
Channel %1 program control: action %2 not allowed |
16906 |
Channel %1 program control: action %2 is aborted due to an alarm |
16907 |
Channel %1 action %2 only possible in stop state |
16908 |
Channel %1 action %2 only possible in reset state or at the block end |
16909 |
Channel %1 action %2 not allowed in current mode |
16911 |
Channel %1 mode change is not allowed |
16912 |
Channel %1 program control: action %2 only possible in reset state |
16913 |
Mode group %1 channel %2 mode change: action %3 not allowed |
16914 |
Mode group %1 channel %2 mode change: action %3 not allowed |
16915 |
Channel %1 action %2 not allowed in the current block |
16916 |
Channel %1 repositioning: action %2 not allowed in the current state |
16918 |
Channel %1 for action %2 all channels must be in reset state |
16919 |
Channel %1 action %2 is not allowed due to a pending alarm |
16920 |
Channel %1 action %2 is already active |
16921 |
Channel %1 mode group %2 machine data: channel/mode group assignment not allowed or assigned twice |
16922 |
Channel %1 subprograms: action %2 maximum nesting depth exceeded |
16923 |
Channel %1 program control: action %2 not allowed in the current state |
16924 |
Channel %1 caution: program test modifies tool management data |
16925 |
Channel %1 program control: action %2 not allowed in the current state, action %3 active |
16926 |
Channel %1 channel coordination: action %2 not allowed in block %3, marker %4 is already set |
16927 |
Channel %1 action %2 at active interrupt treatment not allowed |
16928 |
Channel %1 interrupt treatment: action %2 not possible |
16930 |
Channel %1: preceding block and current block %2 must be separated through an executable block |
16931 |
Channel %1 subprograms: action %2 maximum nesting depth exceeded |
16932 |
Channel %1 conflict when activating user data type %2 |
16933 |
Channel %1 interrupt treatment: action %2 not allowed in the current state |
16934 |
Channel %1 interrupt treatment: action %2 not possible due to stop |
16935 |
Channel %1 action %2 not possible due to search run |
16936 |
Channel %1 action %2 not possible due to active dry run |
16937 |
Channel %1 action %2 not possible due to program test |
16938 |
Channel %1 action %2 aborted due to active gear change |
16939 |
Channel %1 action %2 rejected due to active gear change |
16940 |
Channel %1 action %2 wait for gear change |
16941 |
Channel %1 action %2 rejected because no program event has been executed yet |
16942 |
Channel %1 start program command action %2 not possible |
16943 |
Channel %1 action %2 not possible due to ASUP |
16944 |
Channel %1 action %2 not possible due to active search blocks |
16945 |
Channel %1 action %2 delayed up to the block end |
16946 |
Channel %1 start via START is not allowed |
16947 |
Channel %1 start via PLC is not allowed |
16948 |
Channel %1 dependent channel %2 still active |
16949 |
Correspondence between marker of channel %1 and channel %2 is invalid. |
16950 |
Channel %1 search run with hold block |
16951 |
Channel %1 search run in a program section that cannot be searched |
17000 |
Channel %1 block %2 maximum number of symbols exceeded |
17001 |
Channel %1 block %2 no memory left for tool/magazine data |
17010 |
Channel %1 block %2 no memory left |
17020 |
Channel %1 block %2 illegal array index 1 |
17030 |
Channel %1 block %2 illegal array index 2 |
17040 |
Channel %1 block %2 illegal axis index |
17050 |
Channel %1 block %2 illegal value |
17055 |
Channel %1 block %2 GUD variable not existing |
17060 |
Channel %1 block %2 requested data area too large |
17070 |
Channel %1 block %2 data is write-protected |
17080 |
Channel %1 block %2 %3 value below lower limit |
17090 |
Channel %1 block %2 %3 value exceeds upper limit |
17095 |
Channel %1 block %2 invalid value |
17100 |
Channel %1 block %2 digital input/comparator no. %3 not activated |
17110 |
Channel %1 block %2 digital output no. %3 not activated |
17120 |
Channel %1 block %2 analog input no. %3 not activated |
17130 |
Channel %1 block %2 analog output no. %3 not activated |
17140 |
Channel %1 block %2 NCK output %3 is assigned to a function via machine data |
17150 |
Channel %1 block %2 maximum of %3 NCK outputs programmable in the block |
17160 |
Channel %1 block %2 no tool selected |
17170 |
Channel %1 block %2 number of symbols too large |
17180 |
Channel %1 block %2 illegal D number |
17181 |
Channel %1 block %2 T no.= %3, D no.= %4 not existing |
17182 |
Channel %1 block %2 illegal sum correction number |
17188 |
Channel %1 D number %2 defined in tool T no. %3 and %4 |
17189 |
Channel %1 D number %2 of tools defined on magazine/location %3 and %4 |
17190 |
Channel %1 block %2 illegal T number |
17191 |
Channel %1 block %2 T= %3 not existing, program %4 |
17192 |
TO unit %1 invalid tool designation of ‘%2’, duplo no. %3. No more replacement tools possible in ‘%4’. |
17193 |
Channel %1 block %2 the active tool is no longer on toolholder no./spindle no. %3, program %4 |
17194 |
Channel %1 block %2 no suitable tool found |
17200 |
Channel %1 block %2 deleting tool data not possible |
17202 |
Channel %1 block %2 deleting magazine data not possible |
17210 |
Channel %1 block %2 access to variable not possible |
17212 |
Channel %1 tool management: Load manual tool %3, duplo no. %2 onto spindle/ toolholder %4 |
17214 |
Channel %1 tool management: remove manual tool %3 from spindle/toolholder %2 |
17216 |
Channel %1 tool management: remove manual tool from spindle/toolholder %4 and load manual tool %3, duplo no. %2 |
17220 |
Channel %1 block %2 tool not existing |
17230 |
Channel %1 block %2 Duplo no. already assigned |
17240 |
Channel %1 block %2 illegal tool definition |
17250 |
Channel %1 block %2 illegal magazine definition |
17260 |
Channel %1 block %2 illegal magazine location definition |
17262 |
Channel %1 block %2 illegal tool adapter operation |
17270 |
Channel %1 block %2 call-by-reference: illegal variable |
17500 |
Channel %1 block %2 axis %3 is not an indexing axis |
17501 |
Channel %1 block %2 indexing axis %3 with Hirth tool system is active |
17502 |
Channel %1 block %2 indexing axis %3 with Hirth tooth system stop is delayed |
17503 |
Channel %1 block %2 indexing axis %3 with Hirth tooth system and axis not referenced |
17510 |
Channel %1 block %2 invalid index for indexing axis %3 |
17600 |
Channel %1 block %2 preset on transformed axis %3 not possible |
17605 |
Channel %1 block %2 axis %3 transformation active: inhibits rotation of axis container |
17610 |
Channel %1 block %2 axis %3 involved in the transformation, action cannot be carried out |
17620 |
Channel %1 block %2 approaching fixed point for transformed axis %3 not possible |
17630 |
Channel %1 block %2 referencing for transformed axis %3 not possible |
17640 |
Channel %1 block %2 spindle operation for transformed axis %3 not possible |
17650 |
Channel %1 block %2 machine axis %3 not programmable |
17800 |
Channel %1 block %2 illegally coded position programmed |
17900 |
Channel %1 block %2 axis %3 is no machine axis |
18000 |
Channel %1 block %2 NCK-specific protection zone %3 wrong. Error code %4 |
18001 |
Channel %1 block %2 channel-specific protection zone %3 incorrect. Error code %4 |
18002 |
Channel %1 block %2 NCK protection zone %3 cannot be activated. Error code %4 |
18003 |
Channel %1 block %2 NCK protection zone %3 cannot be activated.Error code %4 |
18004 |
Channel %1 block %2 orientation of workpiece-related protection zone %3 does not correspond to the orientation of tool-related protection zone %4 |
18005 |
Channel %1 block %2 serious error in definition of NCK-specific protection zone %3 |
18006 |
Channel %1 block %2 serious error in definition of channel-specific protection zone %3 |
18100 |
Channel %1 block %2 invalid value assigned to FXS[] |
18101 |
Channel %1 block %2 invalid value assigned to FXST[] |
18102 |
Channel %1 block %2 invalid value assigned to FXSW[] |
18200 |
Channel %1 block %2 curve table: block search stop not allowed with definition CTABDEF |
18201 |
Channel %1 block %2 curve table: table %3 does not exist |
18202 |
Channel %1 block %2 curve table: instruction CTABEND without CTABDEF not allowed |
18300 |
Channel %1 block %2 frame: fine shift not possible |
18310 |
Channel %1 block %2 frame: illegal rotation |
18311 |
Channel %1 block %2 frame: illegal instruction |
18312 |
Channel %1 block %2 frame: fine shift not configured |
18313 |
Channel %1 block %2 frame: illegal switchover of geometry axes |
18314 |
Channel %1 block %2 frame: type conflict |
18400 |
Channel %1 block %2 language change not possible: |
20000 |
Channel %1 axis %2 reference cam not reached |
20001 |
Channel %1 axis %2 no cam signal present |
20002 |
Channel %1 axis %2 zero mark not found |
20003 |
Channel %1 axis %2 measuring system error |
20004 |
Channel %1 axis %2 reference mark missing |
20005 |
Channel %1 axis %2 reference point approach aborted |
20006 |
Channel %1 axis %2 reference point creep velocity not reached |
20007 |
Channel %1 axis %2 reference point approach requires 2 measuring systems |
20008 |
Channel %1 axis %2 reference point approach requires second referenced measuring system |
20050 |
Channel %1 axis %2 handwheel mode active |
20051 |
Channel %1 axis %2 handwheel mode not possible |
20052 |
Channel %1 axis %2 already active |
20053 |
Channel %1 axis %2 DRF, FTOCON, external zero point offset not possible |
20054 |
Channel %1 axis %2 wrong index for indexing axis in JOG mode |
20055 |
Channel %1 master spindle not present in JOG mode |
20056 |
Channel %1 axis %2 no revolutional feedrate possible. Axis/spindle %3 stationary |
20057 |
Channel %1 block %2 revolutional feedrate for axis/spindle %3 is |
20058 |
Channel %1 axis %2 revolutional feedrate: illegal feed source |
20060 |
Channel %1 axis %2 cannot be traversed as geometry axis |
20061 |
Channel %1 axis %2 cannot be traversed as orientation axis |
20062 |
Channel %1 axis %2 already active |
20063 |
Channel %1 axis %2 orientation axes cannot be traversed without transformation |
20065 |
Channel %1 master spindle not defined for geometry axes in JOG mode |
20070 |
Channel %1 axis %2 programmed end position is behind software limit switch %3 |
20071 |
Channel %1 axis %2 programmed end position is behind working area limit %3 |
20072 |
Channel %1 axis %2 is not an indexing axis |
20073 |
Channel %1 axis %2 cannot be repositioned |
20074 |
Channel %1 axis %2 wrong index position |
20075 |
Channel %1 axis %2 can currently not oscillate |
20076 |
Channel %1 axis %2 oscillating – mode change not possible |
20077 |
Channel %1 axis %2 programmed position is behind software limit switch %3 |
20078 |
Channel %1 axis %2 programmed position is behind working area limit %3 |
20079 |
Channel %1 axis %2 oscillation path length %3 |
20080 |
Channel %1 axis %2 no handwheel assigned for overlaid motion |
20085 |
Channel %1 contour handwheel: traverse direction or overtravel of beginning of block not allowed |
20090 |
Axis %1 travel to fixed stop not possible. Check programming and axis data. |
20091 |
Axis %1 has not reached fixed stop |
20092 |
Axis %1 travel to fixed stop still active |
20093 |
Axis %1 standstill monitoring at fixed-stop end point has been triggered |
20094 |
Axis %1 function has been aborted |
20095 |
Axis %1 illegal torque, current torque %2 |
20096 |
Axis %1 brake test aborted, additional information %2 |
20100 |
Channel %1: invalid configuration for digitizing function |
20101 |
Communication with the digitizer not possible |
20102 |
Channel %1: No or invalid trafo at digitizing active |
20103 |
Channel %1: digitizing module does not support 3+2 axis digitizing |
20105 |
Channel %1: axes stopped by digitizer. Error code: %2 |
20106 |
Emergency stop set by the digitizer |
20108 |
Invalid data package received from the digitizer. Error codes: %1, %2 |
20109 |
Error in communication with the digitizer: status code of com-circuit: %1 |
20120 |
Axis %1: too many compensation relations |
20121 |
Axis %1: Configuration error in compensation table %2 |
20122 |
Compensation table %1: invalid axis assignment |
20123 |
Axis %1: different output assignment of multiplied tables |
20124 |
Axis %1: sum of compensation values too large |
20125 |
Axis %1: change of compensation value is too rapid |
20130 |
Channel %1 contour tunnel monitoring |
20140 |
Channel %1 motion synchronous action: traversing of command axis %2 see NC alarm %3 |
20141 |
Channel %1 motion synchronous action: illegal axis type |
20142 |
Channel %1 command axis %2: rotation of axis container already enabled |
20143 |
Channel %1 axis %2 command axis cannot be started as it is controlled by the PLC |
20144 |
Channel %1 block %2 motion synchronous action: system variable access not possible |
20145 |
Channel %1 block %2 motion synchronous action: arithmetic error |
20146 |
Channel %1 block %2 motion synchronous action: nesting depth exceeded |
20147 |
Channel %1 block %2 motion synchronous action: command not executable |
20148 |
Channel %1 block %2 motion synchronous action: internal error %3 |
20149 |
Channel %1 block %2 motion synchronous action: illegal index |
20150 |
Channel %1 tool management: PLC terminates interrupted command |
20160 |
Channel %1 tool management: PLC can terminate only incorrectly aborted commands |
20170 |
Channel %1 machine data $AC_FIFO invalid |
20200 |
Channel %1 invalid spindle number %2 with tool fine compensation |
20201 |
Channel %1 spindle %2 no tool assigned |
20203 |
Channel %1 no active tool |
20204 |
Channel %1 PUTFTOC command not allowed with FTOCOF |
20210 |
Channel %1 block %3 spindle %2 wrong values for centerless grinding |
20211 |
Channel %1 block %3 spindle %2 support point beyond range limits |
21600 |
Monitoring for ESR active |
21610 |
Channel %1 axis %2 encoder %3 frequency limit exceeded |
21611 |
Channel %1 NC-controlled Extended Stop/Retract triggered |
21612 |
Channel %1 axis %2 VDI signal ‘Servo enable’ reset during motion |
21613 |
Axis %1 measuring system changing |
21614 |
Channel %1 axis %2 hardware limit switch %3 |
21615 |
Channel %1 axis %2 taken from traverse mode to follow-up mode |
21616 |
Channel %1 block %2 overlaid motion active at transformation switchover |
21617 |
Channel %1 block %2 transformation does not allow to traverse the pole |
21618 |
Channel %1 as from block %2 transformation active: overlaid motion too great |
21619 |
Channel %1 block %2 transformation active: motion not possible |
21650 |
Channel %1 axis %2 overlaid motion not allowed |
21660 |
Channel %1 block %2 axis %3 conflict between SYNACT: $AA_OFF and CORROF |
21665 |
Channel %1 $AA_TOFF cleared |
21670 |
Channel %1 block %2 illegal change of tool direction with $AA_TOFF active |
21700 |
Channel %1 block %3 axis %2 touch probe already deflected, edge polarity not possible |
21701 |
Channel %1 block %3 axis %2 measurement not possible |
21702 |
Channel %1 block %3 axis %2 measurement aborted |
21703 |
Channel %1 block %3 axis %2 touch probe not deflected, illegal edge polarity |
21740 |
Output value at analog output no. %1 has been limited |
21750 |
Error during output of cam signals via timer |
21760 |
Channel %1 block %2 too many auxiliary functions programmed |
21800 |
Channel %1 workpiece setpoint %2 reached |
22000 |
Channel %1 block %3 spindle %2 change of gear stage not possible |
22010 |
Channel %1 block %3 spindle %2 actual gear stage differs from requested gear stage |
22011 |
Channel %1 block %3 spindle %2 change to programmed gear stage not possible |
22012 |
Channel %1 block %2 leading spindle %3 is in simulation. |
22013 |
Channel %1 block %2 dependent spindle %3 is in simulation. |
22014 |
Channel %1 block %2. The dynamics of leading spindle %3 and dependent spindle %4 is too variably |
22020 |
Channel %1 block %3 spindle %2 gear step change position not reached |
22040 |
Channel %1 block %3 spindle %2 is not referenced with zero marker |
22045 |
Block %2 spindle/axis %3 not available in channel %1 because active in channel %4 |
22050 |
Channel %1 block %3 spindle %2 no transition from speed control mode to position control mode |
22051 |
Channel %1 block %3 spindle %2 reference mark not found |
22052 |
Channel %1 block %3 spindle %2 no standstill on block change |
22053 |
Channel %1 block %3 spindle %2 reference mode not supported |
22054 |
Channel %1 block %3 spindle %2 improper punching signal |
22055 |
Channel %1 block %3 spindle %2 configured positioning speed is too high |
22060 |
Channel %1 position control expected for axis/spindle %2 |
22062 |
Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is not reached |
22064 |
Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is too high |
22065 |
Channel %1 tool management: Tool motion is not possible, as tool %2 with Duplo no. %3 is not in magazine %4 |
22066 |
Channel %1 tool management: Tool change is not possible, as tool %2 with Duplo no. %3 is not in magazine %4 |
22067 |
Channel %1 tool management: tool change not possible since there is no tool available in tool group %2 |
22068 |
Channel %1 block %2 tool management: no tool available in tool group %3 |
22069 |
Channel %1 block %2 tool management: No tool available in tool group %3, program %4 |
22070 |
TO unit %1 Please change tool T= %2 into magazine. Repeat data backup |
22071 |
TO unit %1 tool %2 duplo no. %3 is active, but not in the magazine area under consideration |
22100 |
Channel %1 block %3 spindle %2 chuck speed exceeded |
22200 |
Channel %1 spindle %2 axis stopped during tapping |
22250 |
Channel %1 spindle %2 axis stopped during thread cutting |
22260 |
Channel %1 spindle %2 thread might be damaged |
22270 |
Channel %1 block %2 maximum velocity of thread axis at position %3 reached |
22275 |
Channel %1 block %2 zero velocity of thread axis at position %3 reached |
22280 |
Channel %1 in block %2: Prog. acceleration path too short %3, %4 required |
22320 |
Channel %1 block %2 PUTFTOCF command could not be transferred |
22321 |
Channel %1 axis %2 PRESET not allowed during traverse motion |
22322 |
Channel %1 axis %2 PRESET: illegal value |
25000 |
Axis %1 hardware fault of active encoder |
25001 |
Axis %1 hardware fault of passive encoder |
25010 |
Axis %1 pollution of measuring system |
25011 |
Axis %1 pollution of passive encoder |
25020 |
Axis %1 zero mark monitoring of active encoder |
25021 |
Axis %1 zero mark monitoring of passive encoder |
25022 |
Axis %1 encoder %2 warning %3 |
25030 |
Axis %1 actual velocity alarm limit |
25031 |
Axis %1 actual velocity warning limit |
25040 |
Axis %1 standstill monitoring |
25042 |
Axis %1 standstill monitoring during torque/force limitation |
25050 |
Axis %1 contour monitoring |
25060 |
Axis %1 speed setpoint limitation |
25070 |
Axis %1 drift value too large |
25080 |
Axis %1 positioning monitoring |
25100 |
Axis %1 measuring system switchover not possible |
25105 |
Axis %1 measuring systems differ considerably |
25110 |
Axis %1 selected encoder not available |
25200 |
Axis %1 requested set of parameters invalid |
25201 |
Axis %1 drive fault |
25202 |
Axis %1 waiting for drive |
26000 |
Axis %1 clamping monitoring |
26001 |
Axis %1 parameterization error: friction compensation |
26002 |
Axis %1 encoder %2 parameterization error: number of encoder marks |
26003 |
Axis %1 parameterization error: lead screw pitch |
26004 |
Axis %1 encoder %2 parameterization error: grid point distance with linear encoders |
26005 |
Axis %1 parameterization error: output rating |
26006 |
Axis %1 encoder %2 encoder type/output type %3 not possible |
26007 |
Axis %1 QEC: invalid coarse step size |
26008 |
Axis %1 QEC: invalid fine step size |
26009 |
Axis %1 QEC: memory overflow |
26010 |
Axis %1 QEC: invalid acceleration characteristic |
26011 |
Axis %1 QEC: invalid measuring periods |
26012 |
Axis %1 QEC: feed forward control not active |
26014 |
Axis %1 machine data %2 invalid value |
26015 |
Axis %1 machine data %2[%3] invalid value |
26016 |
Axis %1 machine data %2 invalid value |
26017 |
Axis %1 machine data %2[%3] invalid value |
26018 |
Axis %1 setpoint output drive %2 used more than once |
26019 |
Axis %1 encoder %2 measurement not possible with this controller module |
26020 |
Axis %1 encoder %2 hardware fault %3 during encoder initialization |
26022 |
Axis %1 encoder %2 measurement with simulated encoder not possible |
26024 |
Axis %1 machine data %2 value changed |
26025 |
Axis %1 machine data %2[%3] value changed |
26030 |
Axis %1 encoder %2 absolute position lost |
26031 |
Axis %1 configuration error master-slave |
26032 |
Axis %1 master-slave not configured |
26050 |
Axis %1 parameter set change from %2 to %3 not possible |
26051 |
Channel %1 in block %2 unanticipated stop crossed in continuous path mode |
26052 |
Channel %1 in block %2: path velocity too high for auxiliary function output |
26070 |
Channel %1 axis %2 cannot be controlled by the PLC, max. number exceeded |
26072 |
Channel %1 axis %2 cannot be controlled by the PLC |
26074 |
Channel %1 switching off PLC control of axis %2 not allowed in the current state |
26080 |
Channel %1 retraction position of axis %2 not programmed or invalid |
26081 |
Channel %1 axis trigger of axis %2 was activated, but axis is not PLC- controlled |
26100 |
Axis %1 drive %2 sign of life missing |
26101 |
Axis %1 drive %2 communication failure |
26102 |
Axis %1 drive %2 sign of life missing |
26105 |
Drive of axis %1 not found |
26106 |
Encoder %2 of axis %1 not found |
26110 |
Independent drive stop/retract triggered |
27000 |
Axis %1 is not safely referenced |
27001 |
Axis %1 error in a monitoring channel, code %2, values: NCK %3, drive %4 |
27002 |
Axis %1 test stop is running |
27003 |
Checksum error found: %1 %2 |
27004 |
Axis %1, difference safe input %2, NCK %3, drive %4 |
27005 |
Axis %1 error in data cross check: static actual value difference |
27006 |
Axis %1 Test ext. pulse deletion running |
27007 |
Axis %1 acceptance test mode is active |
27008 |
Axis %1 SW limit switch deactivated |
27010 |
Axis %1 tolerance for safe standstill exceeded |
27011 |
Axis %1 safe velocity exceeded |
27012 |
Axis %1 safe end position exceeded |
27013 |
Axis %1 safe braking ramp exceeded |
27020 |
Axis %1 stop E triggered |
27021 |
Axis %1 stop D triggered |
27022 |
Axis %1 stop C triggered |
27023 |
Axis %1 stop B triggered |
27024 |
Axis %1 stop A triggered |
27030 |
Axis %1 function not supported on this 611D module |
27031 |
Axis %1 limit value for safe velocity %2 at gear ratio %3 too large (max. %4) |
27032 |
Axis %1 checksum error of safe monitoring. Confirmation and re-test required! |
27033 |
Axis %1 parameterization of MD %2[%3] invalid |
27034 |
Parameterization of MD %1 invalid |
27090 |
Error in data cross check NCK-PLC, %1[%2], NCK: %3; %4 ALSI |
27091 |
Error in data cross check NCK PLC, stop of %1 |
27092 |
Communication broken off during NCK PLC data cross check, error detected by %1 |
27093 |
Checksum error NCK-SPL, %1, %2, %3 |
27094 |
Write access to system variable %1 only allowed from NCK-SPL |
27095 |
%1 SPL protection not activated |
27096 |
SPL start not allowed |
27100 |
At least one axis is not safely referenced |
27101 |
Axis %1 difference in function safe operational stop, NCK: %2 drive: %3 |
27102 |
Axis %1 difference in function safe velocity %2, NCK: %3 drive: %4 |
27103 |
Axis %1 difference in function safe limit position %2, NCK: %3 drive: %4 |
27104 |
Axis %1 difference in function safe cam plus %2, NCK: %3 drive: %4 |
27105 |
Axis %1 difference in function safe cam minus %2, NCK: %3 drive: %4 |
27106 |
Axis %1 difference in function safe velocity nx, NCK: %2 drive: %3 |
27107 |
Axis %1 difference in function cam modulo monitoring, NCK: %2 drive: %3 |
27124 |
Stop A triggered at least in 1 axis |
27200 |
PROFIsafe: cycle time %1 [ms] too long |
27201 |
PROFIsafe: MD %1[%2]: bus segment %3 error |
27202 |
PROFIsafe: MD %1[%2]: address %3 error |
27203 |
PROFIsafe: MD %1[%2]: SPL assignment error |
27204 |
PROFIsafe: double assignment MD %1[%2] – MD %3[%4] |
27220 |
PROFIsafe: Number of NCK F modules (%1) <> number of DP modules (%2) |
27221 |
PROFIsafe: NCK F module MD %1[%2] unknown |
27222 |
PROFI safe: S7 F module PROFI safe address %1 unknown |
27223 |
PROFIsafe: NCK F module MD %1[%2] is not a %3 module |
27224 |
PROFIsafe: F module MD %1[%2] – MD %3[%4]: double assignment of PROFIsafe address |
27225 |
PROFIsafe: slave %1, configuration error %2 |
27240 |
PROFIsafe: DP M not running up, DP info: %1 |
27241 |
PROFIsafe: DP M version different, NCK: %1, PLC: %2 |
27242 |
PROFIsafe: F module %1, %2 faulty |
27250 |
PROFIsafe: configuration in DP M changed; error code %1 – %2 |
27251 |
PROFIsafe: F module %1, %2 reports error %3 |
27252 |
PROFIsafe: Slave %1, sign-of-life error |
27253 |
PROFIsafe: communication fault F master component %1, error %2 |
27254 |
PROFIsafe: F module %1, error on channel %2; %3 |
27255 |
PROFIsafe: F module %1, general error |
27256 |
PROFIsafe: Current cycle time %1 [ms] > parameterized cycle time |
27299 |
PROFIsafe: Diagnosis %1 %2 %3 %4 |
28000 |
NCU link connection to all other NCUs of the link network has been aborted |
28001 |
NCU link connection to the NCU %1 of the link network has been aborted |
28002 |
Error on activation of machine data, NCU network-wide machine data were modified by NCU %1 |
28004 |
NCU link: NCU %1 of the link network is not on the bus |
28005 |
NCU link: NCU %1 of the link network not running synchronously |
28007 |
NCU link: conflict in configuration data of NCU %1 |
28008 |
NCU link: conflict in timer setting of NCU %1 |
28009 |
NCU link: conflict in bus parameters of NCU %1 |
28010 |
NCU link: the NCU %1 has not received a message |
28011 |
IPO time insufficient for NCU link. Link cycle time: %1 |
28012 |
NCU link: synchronization cycle signal failure %1 times |
28020 |
NCU link: too many link axes configured %1 |
28030 |
Serious alarm on NCU %1, axes in follow-up mode |
28031 |
Serious alarm on NCU %1 not yet acknowledged, axes still in follow-up mode |
28032 |
Emergency stop activated on NCU %1, axes in follow-up mode |
28033 |
Emergency stop on NCU % 1, axes still in follow-up mode |
29033 |
Channel %1 axis change of axis %2 not possible, PLC axis movement not yet completed |
60000 |
Channel %1 block %2: |
61000 |
Channel %1 block %2 no tool compensation active |
61001 |
Channel %1 block %2 thread lead incorrect |
61002 |
Channel %1 block %2 machining type wrongly defined |
61003 |
Channel %1 block %2 no feed programmed in the cycle |
61004 |
Channel %1 block %2 configuration geometry axis incorrect |
61005 |
Channel %1 block %2 3rd geometry axis not present |
61006 |
Channel %1 block %2 tool radius too large |
61007 |
Channel %1 block %2 tool radius too small |
61009 |
Channel %1 block %2 active tool number = 0 |
61010 |
Channel %1 block %2 finishing allowance too large |
61011 |
Channel %1 block %2 scaling not allowed |
61012 |
Channel %1 block %2 different scaling on the plane |
61013 |
Channel %1 block %2 basic settings were changed, program cannot be executed |
61101 |
Channel %1 block %2 reference plane incorrectly defined |
61102 |
Channel %1 block %2 no spindle direction programmed |
61103 |
Channel %1 block %2 number of drillings is zero |
61104 |
Channel %1 block %2 contour violation of slots/long holes |
61105 |
Channel %1 block %2 cutter radius too large |
61106 |
Channel %1 block %2 number or distance of circular elements |
61107 |
Channel %1 block %2 first drilling depth incorrectly defined |
61108 |
Channel %1 block %2 illegal values for parameters _RAD1 and _DP1 |
61109 |
Channel %1 block %2 parameter _CDIR incorrectly defined |
61110 |
Channel %1 block %2 finishing allowance at the base > depth infeed |
61111 |
Channel %1 block %2 infeed width > tool diameter |
61112 |
Channel %1 block %2 tool radius negative |
61113 |
Channel %1 block %2 parameter _CRAD for corner radius too large |
61114 |
Channel %1 block %2 machining direction G41/G42 incorrectly defined |
61115 |
Channel %1 block %2 approach or retract mode (straight line/circle/plane/space) incorrectly defined |
61116 |
Channel %1 block %2 approach or retraction path = 0 |
61117 |
Channel %1 block %2 active tool radius |
61118 |
Channel %1 block %2 length or width = 0 |
61119 |
Channel %1 block %2 nominal or core diameter incorrectly programmed |
61120 |
Channel %1 block %2 internal/external thread type not defined |
61121 |
Channel %1 block %2 number of teeth per cutting edge missing |
61122 |
Channel %1 block %2 safety clearance on the plane incorrectly defined |
61124 |
Channel %1 block %2 infeed width is not programmed |
61125 |
Channel %1 block %2 technology selection in parameter _TECHNO incorrectly defined |
61126 |
Channel %1 block %2 thread length too short |
61127 |
Channel %1 block %2 transmission ratio of tapping axis incorrectly defined (machine data) |
61128 |
Channel %1 block %2 dipping angle = 0 for dipping with oscillation or helix |
61180 |
Channel %1 block %2 no name assigned to swivel data block, although MD $MN_MM_NUM_TOOL_CARRIER > 1 |
61181 |
Channel %1 block %2 NCK software version unsufficient (missing TOOLCARRIER functionality) |
61182 |
Channel %1 block %2 name of swivel data block unknown |
61183 |
Channel %1 block %2 retraction mode GUD7 _TC_FR beyond value range 0… 2 |
61184 |
Channel %1 block %2 no solution possible with current input angle values |
61185 |
Channel %1 block %2 no or incorrect (min > max) rotary axis angle ranges assigned |
61186 |
Channel %1 block %2 rotary axis vectors invalid –> Check installation and start-up of the swivel cycle CYCLE800 |
61188 |
Channel %1 block %2 no axis name for the 1st axis assigned -> Check installation and start-up of the swivel cycle CYCLE800 |
61200 |
Channel %1 block %2 too many elements in the machining block |
61201 |
Channel %1 block %2 wrong sequence in the machining block |
61202 |
Channel %1 block %2 no technology cycle |
61203 |
Channel %1 block %2 no positioning cycle |
61204 |
Channel %1 block %2 unknown technology cycle |
61205 |
Channel %1 block %2 unknown positioning cycle |
61210 |
Channel %1 block %2 block search element not found |
61211 |
Channel %1 block %2 absolute reference missing |
61212 |
Channel %1 block %2 wrong tool type |
61213 |
Channel %1 block %2 circle radius too small |
61214 |
Channel %1 block %2 no lead programmed |
61215 |
Channel %1 block %2 raw dimension incorrectly programmed |
61216 |
Channel %1 block %2 feed/tooth only possible with milling tools |
61217 |
Channel %1 block %2 cutting speed for tool radius 0 programmed |
61218 |
Channel %1 block %2 feed/tooth programmed, but number of teeth is zero |
61222 |
Channel %1 block %2 plane infeed greater than the tool diameter |
61223 |
Channel %1 block %2 approach path too short |
61224 |
Channel %1 block %2 retract path too short |
61225 |
Channel %1 block %2 swivel data block unknown |
61226 |
Channel %1 block %2 swivel head cannot be exchanged |
61230 |
Channel %1 block %2 tool probe diameter too small |
61231 |
Channel %1 block %2 ShopMill program %3 cannot be executed, as it has not been tested by ShopMill |
61232 |
Channel %1 block %2 loading of magazine tool not possible |
61233 |
Channel %1 block %2: Thread inclination incorrectly defined |
61234 |
Channel %1 block %2 ShopMill subroutine %4 cannot be executed, as it has not been tested by ShopMill |
61235 |
Channel %1 block %2: ShopTurn program %4 cannot be executed, as it has not been tested by ShopTurn. |
61236 |
Channel %1 block %2: ShopTurn subroutine %4 cannot be executed, as it has not been tested by ShopTurn. |
61237 |
Channel %1 block %2: Retraction direction unknown. Manually retract tool! |
61238 |
Channel %1 block %2: Machining direction unknown. |
61239 |
Channel %1 block %2: Tool change point lies in the retraction area! |
61240 |
Channel %1 block %2: Wrong feed type |
61241 |
Channel %1 block %2: No retraction plane defined for this machining direction. |
61242 |
Channel %1 block %2: Wrong machining direction |
61243 |
Channel %1 block %2: Correct tool change point, tool tip is in retraction area! |
61244 |
Channel %1 block %2: Thread lead change results in an undefined thread |
61246 |
Channel %1 block %2: Safety clearance too small |
61247 |
Channel %1 block %2: Blank radius too small |
61248 |
Channel %1 block %2: Infeed too small |
61249 |
Channel %1 block %2: Number of edges too small |
61250 |
Channel %1 block %2: Key width/Edge length too small |
61251 |
Channel %1 block %2: Key width/Edge length too large |
61252 |
Channel %1 block %2: Chamfer/Radius too large |
61253 |
Channel %1 block %2: No finishing allowance programmed |
61254 |
Channel %1 block %2: Error when traversing to fixed stop |
61255 |
Channel %1 block %2: Cut-off error: Tool breakage? |
61301 |
Channel %1 block %2 measuring probe does not switch |
61302 |
Channel %1 block %2 measuring probe collision |
61303 |
Channel %1 block %2 safe area exceeded |
61308 |
Channel %1 block %2 check measuring distance 2a |
61309 |
Channel %1 block %2 check measuring probe type |
61310 |
Channel %1 block %2 scale factor is active |
61311 |
Channel %1 block %2 no D number is active |
61316 |
Channel %1 block %2 center point and radius cannot be determined. |
61332 |
Channel %1 block %2 change tool tip position |
61338 |
Channel %1 block %2 positioning velocity is zero |
61601 |
Channel %1 block %2 finished-part diameter too small |
61602 |
Channel %1 block %2 tool width incorrectly defined |
61603 |
Channel %1 block %2 groove form incorrectly defined |
61604 |
Channel %1 block %2 active tool violates programmed contour |
61605 |
Channel %1 block %2 contour incorrectly programmed |
61606 |
Channel %1 block %2 contour processing error |
61607 |
Channel %1 block %2 starting point incorrectly programmed |
61608 |
Channel %1 block %2 wrong cutting edge position programmed |
61609 |
Channel %1 block %2 form incorrectly defined |
61610 |
Channel %1 block %2 no infeed depth programmed |
61611 |
Channel %1 block %2 no intersection point found |
61612 |
Channel %1 block %2 thread axis cutting not possible |
61613 |
Channel %1 block %2 undercut position incorrectly defined |
61800 |
Channel %1 block %2: External CNC system missing |
61801 |
Channel %1 block %2: Wrong G code selected |
61802 |
Channel %1 block %2: Wrong axis type |
61803 |
Channel %1 block %2 programmed axis not present |
61804 |
Channel %1 block %2: Progr. position exceeds reference point |
61805 |
Channel %1 block %2: The value is absolutely and incrementally programmed |
61806 |
Channel %1 block %2: Incorrect axis assignment |
61807 |
Channel %1 block %2 wrong spindle direction programmed (active) |
61808 |
Channel %1 block %2: The final drilling depth or individual drilling depth is missing |
61809 |
Channel %1 block %2: Impermissible drilling position |
61810 |
Channel %1 block %2: ISO-G code not possible |
61811 |
Channel %1 block %2: Impermissible ISO axis name |
61812 |
Channel %1 block %2: Value(s) in the external cycle call incorrectly defined |
61813 |
Channel %1 block %2: GUD value incorrectly defined |
61814 |
Channel %1 block %2: Polar coordinates not possible with cycle |
61815 |
Channel %1 block %2: G40 not active |
61816 |
Channel %1 block %2: axes are not at the reference point |
61817 |
Channel %1 block %2: The axis coordinates are within the protection zone |
61818 |
Channel %1 block %2: The axis area limit values are identical |
62000 |
Channel %1 block %2: |
62100 |
Channel %1 block %2 no drilling cycle active |
62101 |
Channel %1 block %2: Incorrect cutting direction – G3 is generated |
62103 |
Channel %1 block %2: The finishing allowance is not programmed |
62105 |
Channel %1 block %2 number of columns or lines is zero |
62180 |
Channel %1 block %2 no name assigned to swivel data block although machine data $MN_MM_NUM_TOOL_CARRIER > 1 |
62181 |
Channel %1 block %2 NCK software version unsufficient (missing TOOLCARRIER functionality) |
62182 |
Channel %1 block %2: Load swivel head |
62183 |
Channel %1 block %2 retraction mode GUD7 _TC_FR beyond value range 0…2 |
62184 |
Channel %1 block %2 no solution possible with current input angle values |
62185 |
Channel %1 block %2 no end stop assigned to rotary axes |
62186 |
Channel %1 block %2 illegal rotary axis vectors |
62187 |
Channel %1 block %2 name of swivel data block unknown |
62200 |
Channel %1 block %2: Start spindle |
63000 |
Channel %1 block %2: |
65000 |
Channel %1 block %2: |
66000 |
Channel %1 block %2: |
67000 |
Channel %1 block %2: |
68000 |
Channel %1 block %2: |
70000 |
Compile cycle alarm |
75000 |
OEM alarm |
75005 |
Channel %1 block %2 CLC: General programming error |
75010 |
Channel %1 block %2 CLC_LIM value exceeds MD limit |
75015 |
Channel %1 block %2 CLC(0) with active TOC |
75016 |
Channel %1 block %2 CLC: orientation changed for TRAFOOF |
75020 |
Channel %1 CLC position offset at lower limit %2 |
75021 |
Channel %1 CLC position offset at upper limit %2 |
75025 |
Channel %1 CLC stopped because sensor head has been touched |
75050 |
Channel %1 wrong MD configuration, error code %2 |
75051 |
Channel %1 CC_COPON CC_COPOFF error code %2 |
75060 |
Channel %1 tolerance window exceeded axis %2 |
75061 |
Channel %1 coupling active axis %2 |
75062 |
Channel %1 axes not in standstill axis %2 |
75070 |
Channel %1 wrong machine data for collision protection %2 |
75071 |
Channel %1 collision monitoring axis %2 |
75100 |
Too many analog axes configured |
75110 |
Axis %1 reached drift limit |
75200 |
Channel %1 wrong MD configuration, %2 incorrect |
75210 |
Channel %1 number of axes/axis assignment inconsistent |
75250 |
Channel %1 tool parameters incorrect |
75255 |
Channel %1 working area error |
75260 |
Channel %1 block %2 tool parameters incorrect |
75265 |
Channel %1 block %2 working area error |
75270 |
Channel %1 tool parameters incorrect |
75275 |
Channel %1 block %2 working area error |
75451 |
Error with definition of setpoint switchover |
75452 |
Axis %1 setpoint switchover not possible in the current state |
75500 |
Channel %1 wrong configuration |
75600 |
Channel %1 retrace support: wrong MD configuration. Error code %2 |
75601 |
Channel %1 block %2 invalid parameter in CC_PREPRE() |
75605 |
Channel %1 retrace support: internal error, error code %2 |
75606 |
Channel %1 retraceable contour was shortened |
75607 |
Channel %1 resynchronisation not possible |
100300 |
xxx not found |
100301 |
The table cannot be completely generated |
100302 |
No data available – or no access authorization |
100303 |
Paging not possible |
100350 |
Display MD saved |
100351 |
Display MD take-over not possible |
101000 |
No connection to the PLC! |
101001 |
The PLC system status list cannot be read! |
101002 |
Invalid password! |
101003 |
Password for %1 is set! |
101004 |
Password for %1 is set! |
101005 |
The passwords do not match! |
101006 |
Password is deleted! |
101007 |
Password is not set! |
101008 |
Current access level: %1 |
101013 |
Input error – see help – (i)-key |
101016 |
Error: The operand address is greater than 65535! |
101017 |
No PLC input screen forms found! |
101018 |
Reading-in only possible in an active PLC status! |
101100 |
No access authorization! |
101111 |
No axes configured! |
101112 |
No drives configured! |
101113 |
No channels configured! |
101114 |
No MSD configured! |
101115 |
No FDD configured! |
101130 |
Error return value not defined: 00h 00h |
101131 |
No servo disable at PI start |
101132 |
Impermissible execution argument value |
101133 |
MDx120 CURRCTRL_GAIN could not be calculated |
101134 |
MDx407 SPEEDCTRL_GAIN_1 could not be calculated |
101135 |
MDx409 SPEEDCTRL_INTEGRATOR_TIME_1 could not be calculated |
101136 |
MDx150 FIELDCTRL_GAIN could not be calculated |
101137 |
MDx141 MAGNETIZING_REACTANCE=0 |
101138 |
MDx139/MDx140 MD_STATOR-/ROTOR_LEAKAGE_REACTANCE=0 |
101139 |
MDx134 MOTOR_NOMINAL_FREQUENCY=0 |
101140 |
MDx138 ROTOR_COLD_RESISTANCE = 0 |
101141 |
MDx117 MOTOR_INERTIA = 0 |
101142 |
MDx146 < MDx142 MOTOR_MAX_ALLOWED_SPEED < FIELD_WEAKENING_SPEED |
101143 |
MDx142 FIELD_WEAKENING_SPEED = 0 |
101144 |
MDx118 MOTOR_STANDSTILL_CURRENT = 0 |
101145 |
MD1104/1118 MOTOR_MAX_CURRENT/MOTOR_STANDSTILL_CURRENT > 900.0 |
101146 |
Boot file(s) saved |
101147 |
Boot file(s) deleted |
101148 |
Controller MD calculated |
101150 |
MD set active |
101151 |
Start-up successful |
101153 |
MMC-NCK communication faulty %1 %2 |
101154 |
PI service was rejected |
101155 |
Path %1 not available |
101156 |
Impermissible function |
101157 |
File %1 not available |
101158 |
Function not permitted in the current operating state. |
101159 |
Remote block in wrong state |
101160 |
Date and time of the PLC set |
101161 |
The drive is not in cyclic mode! |
101162 |
MDx134/MDx400 MOTOR_NOMINAL_FREQUENCY/MOTOR_RATED_SPEED impermissible |
101163 |
MDx130 MOTOR_NOMINAL_POWER |
101164 |
MDx132 MOTOR_NOMINAL_VOLTAGE |
101165 |
MDx103 MOTOR_NOMINAL_CURRENT |
101166 |
MDx129 POWER_FACTOR_COS_PHI impermissible |
101167 |
MDx134/MDx400 MOTOR_NOMINAL_FREQUENCY/MOTOR_RATED_SPEED impermissible |
101168 |
Warning MDx142 FIELD_WEAKENING_SPEED < MDx400 MOTOR_RATED_SPEED |
101200 |
Safety-Integrated data copied |
101201 |
Safety-Integrated data confirmed |
101202 |
SI data is copied from axis %1 to drive %2 Parameters: %1 = Axis name %2 = Drive number |
101203 |
SI data not completely copied |
101204 |
SI data not confirmed |
101205 |
Drive data changed? -> Don’t forget to save the boot files! |
101206 |
Search action running, pleas wait |
101207 |
Position at $MN_ |
101208 |
SI data confirmed: Axis 1 |
101209 |
SI data confirmed: Drive 1 |
101210 |
The machine data is being prepared for display |
101211 |
NCK address not changed! |
101212 |
NCK address changed! |
101213 |
Invalid NCK address. |
101214 |
Initialization of this window failed! |
101300 |
Please wait – language is being changed |
103000 |
There is no correction block on the NCK |
103001 |
Selection is only possible after being enabled or in the RESET state. |
103002 |
Copying to the clipboard is not possible |
103003 |
MDI clipboard cannot be deleted |
103004 |
Block search not possible |
103006 |
Block search without calculation only possible on the main program level. |
103007 |
Ending overstore is not possible in this channel state. |
103008 |
Block search in channel %1 started – please wait |
103009 |
Conflict between search type and search target! |
103010 |
Invalid file name |
103011 |
No program selected – block search finished |
103014 |
Please reference the axis first |
104000 |
Current tool not found |
104001 |
No other tools available |
104002 |
No other cutting edges available |
104003 |
There aren’t any tools at all |
104004 |
No tool selected |
104005 |
No cutting edge selected |
104006 |
No TO area available in the current channel |
104007 |
Error during tool creation |
104008 |
Error during cutting edge creation |
104011 |
Error during tool deletion |
104012 |
No master spindle available |
104014 |
Incorrect entry |
104015 |
Number of parameters per cutting edge is zero |
104016 |
No spindle available |
104018 |
Tool not available |
104019 |
Tool type not available |
104020 |
No empty location found |
104023 |
Error during tool loading |
104024 |
Error during tool unloading |
104025 |
No magazine configured |
104026 |
Notice: Tool is being loaded! |
104027 |
Notice: Tool is being unloaded! |
104029 |
Loading to this location not possible |
104030 |
No more data available |
105000 |
Error x y |
105001 |
Cycle description sc.com not available |
105002 |
File xxx already exists |
105003 |
Workpiece xxx already exists |
105004 |
Clipboard empty! To PASTE, COPY first |
105005 |
Only workpieces can be inserted here |
105006 |
Only files can be inserted here |
105007 |
No name specified |
105008 |
Memory error while writing a cycle call |
105009 |
No write-authorization for the data |
105010 |
No data selected |
105011 |
Cycle description cov.com not available |
105012 |
The program is not or only partially editable (NC reset) |
105013 |
The copied data can be inserted with the soft key “Paste” |
105014 |
Error while copying! |
105015 |
Error while renaming! |
105016 |
Error while deleting! |
105017 |
Selection is only possible after being enabled or in the RESET state. |
105018 |
Error during program generation! |
105019 |
Error while opening a window! |
105020 |
Error while closing a window! |
105021 |
Error during workpiece generation! |
105022 |
Error during enabling! |
105023 |
File exists already! |
105024 |
Check values! – At least 1 value lies outside the input limits! |
105025 |
Please wait, the directory is being prepared! |
105026 |
Notice! The simulated program and edited program are not the same! |
105030 |
Please wait, renumbering is being carried out! |
105031 |
Renumbering was aborted! |
105032 |
Renumbering finished! |
105041 |
Block number is too large! |
105042 |
Impermissible block number! |
105043 |
Impermissible increment! |
105050 |
Please wait: Graphic is being output! |
105051 |
Output of dynamic long texts for cycle parameterization |
105052 |
Error in the cycle description of the ! |
105053 |
No cycle available in current line! |
105054 |
Error during cycle description call! |
105060 |
Please wait: Initilization of the cycle support |
105061 |
Error when opening the file! |
105062 |
Error when closing the file! |
105063 |
Error when positioning in the file %1! |
105064 |
Error when reading the file! |
105070 |
Please wait: Initialization of the simulation started! |
105075 |
Not enough axes in the current channel? > Contour with default axis names: X, Z ! |
109001 |
No switchover: Switchover disable set in current PLC |
109002 |
No switchover: Target PLC occupied, try again |
109003 |
No switchover: Switchover disable set in target PLC |
109004 |
No switchover: PLC occupied by higher-priority MMC’s |
109005 |
No switchover: No displaceable MMC at the target PLC |
109006 |
No switchover: Selected channel invalid |
109007 |
Channel switchover running |
109008 |
Activation is running |
111001 |
Non-interpretable step in line %1 |
111002 |
Insufficient memory, abort in line %1 |
111003 |
ManualTurn: %1 |
111004 |
File faulty or not available: %1 |
111005 |
Error when interpreting the contour %1 Parameters: %1 = Contour name |
111006 |
Maximum number of contour elements exceeded %1 |
111007 |
Error in line %1 %2 |
111008 |
Spindle not synchronized |
111009 |
Load new tool: T%1 Parameters: %1 = Tool number |
111010 |
Teach-in interruption: Log overflow |
111100 |
Wrong position programmed for the spindle |
111105 |
No measuring system available |
111106 |
No spindle stop for a block change |
111107 |
Reference mark not found |
111108 |
No transition from speed control mode to position control mode |
111109 |
Configured positioning velocity is too high |
111110 |
Velocity/Speed is negative |
111111 |
Setpoint speed is zero |
111112 |
Invalid gear stage |
111115 |
Programmed position was not reached |
111126 |
Absolute value minus not possible |
111127 |
Absolute value plus not possible |
111200 |
Spindle positioning error |
111300 |
NC start key defective |
111301 |
NC stop key defective |
111302 |
Spindle start key defective |
111303 |
Spindle stop key defective |
111304 |
Connection to the PLC broken off |
111305 |
Asynchronous subroutine was not executed |
111306 |
Error when selecting or deselecting constant cutting speed |
111307 |
Error when deleting handwheel offset |
111308 |
Error when setting upper spindle speed limit |
111309 |
Error when selecting tool |
111310 |
Error when selecting zero offset |
111311 |
NC start not possible: Deselect single block |
111400 |
Unknown PLC error |
111410 |
Tool %1 was created |
111411 |
%1 Tool(s) can (could) not be created |
111420 |
Error during the inch/metric conversion! Check all data! |
111430 |
Program not loaded. Error when converting old cycles in G code. No NC memory. |
111900 |
Start only possible in basic display |
111901 |
Contour is contained in the current program, machining not enabled |
111902 |
Start only with valid reference point |
111904 |
4. Axis not configured, i.e., no driven tool possible |
112045 |
Several insertion points required |
112046 |
Main contour cannot be bypassed |
112052 |
No residual material generated |
112057 |
Programmed helix violates contour |
112099 |
System-error contour pocket |
112100 |
Error during renumbering. Original state restored. |
112200 |
The contour is a step in the current program sequence. Machining not enabled |
112201 |
The contour is a step in the current automatic sequence. Machining not enabled |
112210 |
Tool axis cannot be switched over. Insufficient NC memory. |
112211 |
Tool preselection could not be processed. Insufficient NC memory. |
112300 |
Tool management type 2 not possible. Magazine not completely loaded. |
112301 |
Tool management type 2 not possible. The magazine is not sorted as in the tool list. |
112323 |
Replace swivel head. |
112324 |
Load swivel head. |
112325 |
Exchange swivel head. |
112326 |
Set swivel head |
112327 |
Angle not in permissible area |
112328 |
Angle adapted to angle grid. |
112329 |
Set swivel head/table |
112330 |
Set swivel table. |
112350 |
No swivel data set up. |
112360 |
The step was not accepted into the program sequence, as the program is running. |
112400 |
Is not available in the tool management |
112401 |
Tool could not be created |
112420 |
Error during the inch/metric conversion! Check all data! |
112502 |
Insufficient memory, abort in line %1 |
112504 |
File faulty or not available: %1 Parameters: %1 = File name |
112505 |
Error when interpreting the contour %1 |
112506 |
Maximum number of contour elements exceeded %1 |
112541 |
Program cannot be interpreted |
112604 |
Connection to the PLC broken off |
112605 |
Asynchronous subroutine was not executed |
112650 |
Unknown PLC error |
112999 |
Faulty grafic data. Exit graphic and restart |
120000 |
Area %1 cannot be loaded! Acknowledge alarm, press area switchover key! |
120001 |
Area %1 cannot be selected. Please deactivate area %2 |
120002 |
Area %1 is still active. Please deactivate area %1 |
120003 |
Area %1 cannot be deactivated. Please try again |
120005 |
Please acknowledge the dialog box in area %1 |
120006 |
The channel switchover is currently disabled by area %1. |
120007 |
The channel switchover is currently disabled. |
120008 |
Control unit switchover, PLC timeout: 001 control unit switchover, PLC timeout: 002 control unit switchover, PLC timeout: 003 |
120120 |
The alarm list is full of alarm texts: Number of alarm texts too high Alarm texts: File %1 not found alarm texts: Input/Output error in file %1 alarm texts: Input/Output error alarm texts: Error when reading from the index file alarm texts: Error when writing in the index file alarm texts: Syntax error in alarm text file %1 |
120200 |
Image preparation suppressed |
120201 |
Communication failure |
120202 |
Waiting for a connection to the NC |
120301 |
Faulty entry for hardkey ‘Program’ in Keys.ini. |
120302 |
The selection is not possible. A program has to have been edited first via the area ‘Program’. |
120303 |
The selection is not possible. The edited file %1 no longer exists. |
120304 |
The selection is not possible. The file %1 has insufficient read rights. |
120305 |
Selection is not possible. The file %1 is currently being edited. |
120306 |
The selection is not possible. The file %1 is selected and active in channel %2. |
120307 |
The file %1 cannot be opened for the editor because it is selected in channel %2 for execution from external sources. |
120308 |
In the event of an emergency stop, the program %1 can only be changed in the machine/program correction area. |
120309 |
The selection is not possible. Please close the simulation and repeat the selection. |
120310 |
The selection is not possible. Please wait for the pending action or terminate it, then repeat the selection. |
300000 |
Hardware drive bus: DCM not present |
300001 |
Axis %1 drive number %2 not possible |
300002 |
Axis %1 drive number %2 assigned twice |
300003 |
Axis %1 drive %2 wrong module type %3 |
300004 |
Axis %1 drive %2 wrong drive type %3 (FDD/MSD) |
300005 |
At least one module found on drive bus that has not been configured |
300006 |
Module with drive number %1 has not been found on drive bus |
300007 |
Axis %1 drive %2 not present or inactive |
300008 |
Axis %1 drive %2 measuring circuit %3 is not available |
300009 |
Axis %1 drive %2 measuring circuit %3 wrong measuring circuit type (type %4 used) |
300010 |
Axis %1 drive %2 active without NC axis assignment |
300011 |
Axis %1 drive %2 hardware version of spindle not supported |
300012 |
Axis %1 drive %2 hardware version of control module not supported |
300020 |
Drive %1 removed for diagnosis |
300100 |
Drive power failure |
300101 |
Bus communications failure |
300200 |
Drive bus hardware fault |
300201 |
Axis %1 drive %2 timeout during access, error location %3 |
300202 |
Axis %1 drive %2 CRC error, error location %3 |
300300 |
Axis %1 drive %2 boot error, error code %3 |
300400 |
Axis %1 drive %2 system error, error codes %3, %4 |
300401 |
Drive software for type %1, block %2 missing or incorrect |
300402 |
System error in drive link. Error codes %1, %2 |
300403 |
Axis %1 drive %2 drive software and drive MD with different version numbers |
300404 |
Axis %1 drive %2 drive MD contains different drive number |
300405 |
Axis %1 drive %2 unknown drive alarm, code %3 |
300410 |
Axis %1 drive %2 error when storing a file (%3, %4) |
300411 |
Axis %1 drive %2 error when reading a file (%3, %4) |
300412 |
Error when storing a file (%1, %2) |
300413 |
Error when reading a file (%1, %2) |
300423 |
Measuring results could not be read (%1) |
300500 |
Axis %1 drive %2 system error, error codes %3, %4 |
300501 |
Axis %1 drive %2 maximum current monitoring |
300502 |
Axis %1 drive %2 maximum current monitoring of phase current R |
300503 |
Axis %1 drive %2 maximum current monitoring of phase current S |
300504 |
Axis %1 drive %2 measuring circuit error of motor measuring system |
300505 |
Axis %1 drive %2 measuring circuit error of absolute track, code %3 |
300506 |
Axis %1 drive %2 NC sign-of-life failure |
300507 |
Axis %1 drive %2 synchronization error of rotor position |
300508 |
Axis %1 drive %2 zero mark monitoring of motor measuring system |
300509 |
Axis %1 drive %2 current frequency exceeded |
300510 |
Axis %1 drive %2 error on actual current measurement zero balancing |
300511 |
Axis %1 drive %2 measuring function active |
300515 |
Axis %1 drive %2 power section heat sink temperature exceeded |
300604 |
Axis %1 drive %2 motor encoder is not adjusted |
300605 |
Axis %1 drive %2 motor change not valid |
300606 |
Axis %1 drive %2 flux controller at limit |
300607 |
Axis %1 drive %2 current controller at limit |
300608 |
Axis %1 drive %2 speed controller at limit |
300609 |
Axis %1 drive %2 encoder cut-off frequency exceeded |
300610 |
Axis %1 drive %2 rotor position identification failed |
300611 |
Axis %1 drive %2 generator mode: Motion at rotor position identification |
300612 |
Axis %1 drive %2 illegal current during rotor position identification |
300613 |
Axis %1 drive %2 maximum permissible motor temperature exceeded |
300614 |
Axis %1 drive %2 time monitoring of motor temperature |
300701 |
Axis %1 drive %2 start-up required |
300702 |
Axis %1 drive %2 base cycle time invalid |
300703 |
Axis %1 drive %2 current cycle time invalid |
300704 |
Axis %1 drive %2 speed controller cycle time invalid |
300705 |
Axis %1 drive %2 position controller cycle time invalid |
300706 |
Axis %1 drive %2 monitoring cycle time invalid |
300707 |
Axis %1 drive %2 basic cycle times of axes differ |
300708 |
Axis %1 drive %2 current controller cycle times of axes differ |
300709 |
Axis %1 drive %2 speed controller cycle times of axes differ |
300710 |
Axis %1 drive %2 position controller cycle times of axes differ |
300711 |
Axis %1 drive %2 monitoring cycle times of axes differ |
300712 |
Axis %1 drive %2 configuration of controller structure (higher dynamic response) not possible |
300713 |
Axis %1 drive %2 lead time for position controller invalid |
300714 |
Axis %1 drive %2 power section code invalid |
300715 |
Axis %1 drive %2 maximum power section current less than or equal to zero |
300716 |
Axis %1 drive %2 torque constant less than or equal to zero |
300717 |
Axis %1 drive %2 motor moment of inertia less than or equal to zero |
300718 |
Axis %1 drive %2 calculation dead time of current controller less than or equal to zero |
300719 |
Axis %1 drive %2 motor not parameterized for delta operation |
300720 |
Axis %1 drive %2 maximum motor speed invalid |
300721 |
Axis %1 drive %2 zero-load current greater than rated motor current |
300722 |
Axis %1 drive %2 zero-load motor current greater than rated current of power section |
300723 |
Axis %1 drive %2 STS configuration of axes differ |
300724 |
Axis %1 drive %2 number of pole pairs invalid |
300725 |
Axis %1 drive %2 number of encoder marks of measuring system invalid |
300726 |
Axis %1 drive %2 voltage constant is zero |
300727 |
Axis %1 drive %2 reactance less than or equal to zero |
300728 |
Axis %1 drive %2 adaption factor torque/current too high |
300729 |
Axis %1 drive %2 motor zero-speed current less than or equal to zero |
300730 |
Axis %1 drive %2 rotor resistance invalid |
300731 |
Axis %1 drive %2 rated power less than or equal to zero |
300732 |
Axis %1 drive %2 rated speed less than or equal to zero |
300733 |
Axis %1 drive %2 zero load voltage invalid |
300734 |
Axis %1 drive %2 zero load current less than or equal to zero |
300735 |
Axis %1 drive %2 field weakening speed invalid |
300736 |
Axis %1 drive %2 Lh characteristic invalid |
300737 |
Axis %1 drive %2 configuration of two EnDat encoders not possible |
300738 |
Axis %1 drive %2 module number for measuring system not possible |
300739 |
Axis %1 drive %2 measuring system already used as motor measuring system |
300740 |
Axis %1 drive %2 measuring system used several times |
300741 |
Axis %1 drive %2 asynchronous mode: feedforward control gain out of range |
300742 |
Axis %1 drive %2 voltage/frequency mode: converter frequency invalid |
300743 |
Axis %1 drive %2 function not supported on this 611D controller module |
300744 |
Axis %1 drive %2 safety monitoring checksum invalid, confirmation and acceptance test required! |
300745 |
Axis %1 drive %2 limit values for safe end positions exchanged |
300746 |
Axis %1 drive %2 SBH/SG not enabled |
300747 |
Axis %1 drive %2 monitoring cycle time MD 1300 invalid |
300748 |
Axis %1 drive %2 monitoring cycle times of both axes differ |
300749 |
Axis %1 drive %2 conversion factor between motor and load too large |
300750 |
Axis %1 drive %2 parameterization error in speed control adaption |
300751 |
Axis %1 drive %2 speed control gain too high |
300752 |
Axis %1 drive %2 blocking frequency of setpoint current filter too high |
300753 |
Axis %1 drive %2 rotor position identification current less than minimal value |
300754 |
Axis %1 drive %2 signal number of var. signaling function invalid |
300755 |
Axis %1 drive %2 voltage/frequency mode: motor is turning |
300756 |
Axis %1 drive %2 speed hysteresis of setpoint current smoothing invalid |
300757 |
Axis %1 drive %2 adaption factor of torque limit invalid |
300757 |
Axis %1 drive %2 adaption factor of torque limit invalid |
300758 |
Axis %1 drive %2 generator mode: response voltage > switch-off threshold |
300759 |
Axis %1 drive %2 generator mode: response voltage > monitoring threshold |
300760 |
Axis %1 drive %2 generator mode: emergency retraction speed > max. motor speed |
300761 |
Axis %1 drive %2 generator mode: minimum axis speed > max. motor speed |
300762 |
Axis %1 drive %2 emergency retraction mode/generator mode already active |
300763 |
Axis %1 drive %2 emergency retraction mode/generator mode invalid |
300764 |
Axis %1 drive %2 emergency retraction mode/generator mode not possible |
300765 |
Axis %1 drive %2 measurement of DC link voltage not possible |
300766 |
Axis %1 drive %2 blocking frequency > Shannon frequency |
300767 |
Axis %1 drive %2 natural frequency > Shannon frequency |
300768 |
Axis %1 drive %2 numerator bandwidth > double blocking frequency |
300769 |
Axis %1 drive %2 denominator bandwidth > double natural frequency |
300770 |
Axis %1 drive %2 format error |
300771 |
Axis %1 drive %2 asynchronous mode: converter frequency invalid |
300772 |
Axis %1 drive %2 asynchronous mode: speed control gain too high |
300773 |
Axis %1 drive %2 asynchronous mode: feedforward control structure not possible |
300774 |
Axis %1 drive %2 asynchronous mode: changeover speed invalid |
300775 |
Axis %1 drive %2 fixed link voltage of axes differ |
300776 |
Axis %1 drive %2 measuring circuit monitoring must be active |
300777 |
Axis %1 drive %2 rotor position identification current too high |
300778 |
Axis %1 drive %2 generator mode: converter frequency rotor position identification |
300779 |
Axis %1 drive %2 motor moment of inertia less than or equal to zero |
300780 |
Axis %1 drive %2 zero load current > rated motor current |
300781 |
Axis %1 drive %2 zero load current > rated current of power section |
300782 |
Axis %1 drive %2 reactance less than or equal to zero |
300783 |
Axis %1 drive %2 rotor resistance invalid |
300784 |
Axis %1 drive %2 zero load voltage invalid |
300785 |
Axis %1 drive %2 zero load current less than or equal to zero |
300786 |
Axis %1 drive %2 field weakening speed invalid |
300787 |
Axis %1 drive %2 asynchronous mode: feedforward control gain out of range |
300788 |
Axis %1 drive %2 parameterization error in current control adaption |
300789 |
Axis %1 drive %2 function not supported on this 611D controller module |
300799 |
Axis %1 drive %2 data backup and reboot required |
300850 |
Axis %1 drive %2 parameterization error in speed control adaption |
300854 |
Axis %1 drive %2 signal number of var. signaling function invalid |
300855 |
Axis %1 drive %2 voltage/frequency mode: motor is turning |
300858 |
Axis %1 drive %2 generator mode: response voltage > switch-off threshold |
300859 |
Axis %1 drive %2 generator mode: response voltage > monitoring threshold |
300860 |
Axis %1 drive %2 generator mode: emergency retraction speed > max. motor speed |
300861 |
Axis %1 drive %2 generator mode: minimum axis speed > max. motor speed |
300862 |
Axis %1 drive %2 emergency retraction mode/generator mode already active |
300863 |
Axis %1 drive %2 emergency retraction mode/generator mode invalid |
300864 |
Axis %1 drive %2 emergency retraction mode/generator mode not possible |
300865 |
Axis %1 drive %2 measurement of DC link voltage not possible |
300875 |
Axis %1 drive %2 fixed link voltage of axes differ |
300888 |
Axis %1 drive %2 parameterization error in current control adaption |
300900 |
Axis %1 drive %2 stop A triggered |
300901 |
Axis %1 drive %2 stop B triggered |
300906 |
Axis %1 drive %2 safe braking ramp exceeded |
300907 |
Axis %1 drive %2 tolerance for safe operational stop exceeded |
300908 |
Axis %1 drive %2 stop C triggered |
300909 |
Axis %1 drive %2 stop D triggered |
300910 |
Axis %1 drive %2 stop E triggered |
300911 |
Axis %1 drive %2 error in one monitoring channel |
300914 |
Axis %1 drive %2 safe velocity exceeded |
300915 |
Axis %1 drive %2 safe end positions exceeded |
300950 |
Axis %1 drive %2 is not safely referenced |
300951 |
Axis %1 drive %2 test stop is running |
300952 |
Axis %1 drive %2 acceptance test mode is active |
301701 |
Axis %1 drive %2 limit value for safe velocity too large |
301702 |
Axis %1 drive %2 track inversion incorrect |
301703 |
Axis %1 drive %2 encoder/motor type are not compatible |
301704 |
Axis %1 drive %2 pole pair width/division of linear scale (internal) out of range |
301705 |
Axis %1 drive %2 distance-coded scale incorrectly parameterized |
301706 |
Axis %1 drive %2 parameterization of cam position invalid |
301707 |
Axis %1 drive %2 parameterization of modulo value for safe cam (SN) invalid |
301708 |
Axis %1 drive %2 actual value synchronization not allowed |
301709 |
Axis %1 drive %2 submodule with integrated linearization invalid |
301710 |
Axis %1 drive %2 resolution SSI motor measuring system invalid |
301711 |
Axis %1 drive %2 transmission length SSI motor measuring system invalid |
301712 |
Axis %1 drive %2 multiturn SSI motor measuring system invalid |
301713 |
Axis %1 drive %2 resolution SSI direct measuring system invalid |
301714 |
Axis %1 drive %2 transmission length SSI direct measuring system invalid |
301715 |
Axis %1 drive %2 multiturn SSI direct measuring system invalid |
301716 |
Axis %1 drive %2 SSI direct measuring system without incremental signals not possible |
301717 |
Axis %1 drive %2 SSI transmission timeout |
301718 |
Axis %1 drive %2 combination of motor/power section invalid |
301719 |
Axis %1 drive %2 power section data incomplete |
310505 |
Axis %1 drive %2 measuring circuit error of absolute track, code %3 |
310606 |
Axis %1 drive %2 external valve voltage supply failed |
310607 |
Axis %1 drive %2 valve not responding |
310608 |
Axis %1 drive %2 speed controller at limit |
310609 |
Axis %1 drive %2 encoder cut-off frequency exceeded |
310610 |
Axis %1 drive %2 wrong piston position |
310611 |
Axis %1 drive %2 pressure sensor failed |
310612 |
Axis %1 drive %2 force limitation off |
310701 |
Axis %1 drive %2 speed controller cycle time invalid |
310702 |
Axis %1 drive %2 position controller cycle time invalid |
310703 |
Axis %1 drive %2 monitoring cycle time invalid |
310704 |
Axis %1 drive %2 speed controller cycle times of axes differ |
310705 |
Axis %1 drive %2 monitoring cycle times of axes differ |
310706 |
Axis %1 drive %2 maximum working speed invalid |
310707 |
Axis %1 drive %2 STS configuration of axes differ |
310708 |
Axis %1 drive %2 number of encoder marks of measuring system invalid |
310709 |
Axis %1 drive %2 error in piston diameter or piston rod diameter |
310710 |
Axis %1 drive %2 distance-coded scale incorrectly parameterized |
310750 |
Axis %1 drive %2 feedforward gain too high |
310751 |
Axis %1 drive %2 proportional gain for speed controller too high |
310752 |
Axis %1 drive %2 integral gain for speed controller invalid |
310753 |
Axis %1 drive %2 D component for speed controller invalid |
310754 |
Axis %1 drive %2 friction compensation gradient too high |
310755 |
Axis %1 drive %2 area factor too high |
310756 |
Axis %1 drive %2 controlled system gain is less than or equal to zero |
310757 |
Axis %1 drive %2 blocking frequency > Shannon frequency |
310758 |
Axis %1 drive %2 natural frequency > Shannon frequency |
310759 |
Axis %1 drive %2 bandwidth numerator larger than double blocking frequency |
310760 |
Axis %1 drive %2 bandwidth denominator greater than double natural frequency |
310761 |
Axis %1 drive %2 proportional gain of force controller too high |
310762 |
Axis %1 drive %2 integral gain for force controller invalid |
310763 |
Axis %1 drive %2 D component of force controller invalid |
310764 |
Axis %1 drive %2 controlled system gain for force controller is less than or equal to zero |
310771 |
Axis %1 drive %2 gain in fine area of valve characteristic is less than or equal to zero |
310772 |
Axis %1 drive %2 gain in rough area of valve characteristic is less than or equal to zero |
310773 |
Axis %1 drive %2 gain at end of saturation area of valve characteristic is less than or equal to zero |
310774 |
Axis %1 drive %2 zero area and knee area of valve characteristic overlap |
310775 |
Axis %1 drive %2 knee area and saturation area of valve characteristic overlap |
311710 |
Axis %1 drive %2 resolution SSI motor measuring system invalid |
311711 |
Axis %1 drive %2 transmission length SSI motor measuring system invalid |
311712 |
Axis %1 drive %2 multiturn SSI motor measuring system invalid |
311716 |
Axis %1 drive %2 SSI measuring system without incremental signals not possible |
311717 |
Axis %1 drive %2 SSI transmission timeout |
380001 |
Profibus-DP: startup error, reason %1 parameter %2 %3 %4. |
380003 |
Profibus-DP: operating error, reason %1,parameter %2 %3 %4. |
380005 |
Profibus-DP: bus access conflict, type %1, counter %2 |
380020 |
Profibus-DP: SDB1000 error %1 for SDB source %2 |
380021 |
Profibus-DP: default SDB1000 was loaded |
380022 |
Profibus-DP: configuration of DP master has been changed |
380040 |
Profibus-DP: configuration error %1, parameter %2 |
380050 |
Profibus-DP: multiple assignment of inputs on address %1 |
380051 |
Profibus-DP: multiple assignment of outputs on address %1 |
380060 |
Profibus-DP: alarm %1 on logical address %2 from unassigned station |
380070 |
Profibus DP: no input slot available for base address %1 (length %2) |
380071 |
Profibus DP: no output slot available for base address %1 (size %2) |
380072 |
Profibus DP: output slot for base address %1 (size %2) not allowed |
380075 |
Profibus DP: DP I/O failure slave %1 |
380500 |
Profibus-DP: fault on drive %1, code %2, value %3, time %4 |
400102 |
Delete DB 2 in the PLC and restart |
400103 |
Delete DB 3 in the PLC and restart |
400106 |
Delete DB 3 in the PLC and restart |
400109 |
Delete DB 9 in the PLC and restart |
400171 |
Delete DB 71 in the PLC and restart |
400172 |
Delete DB 72 in the PLC and restart |
400173 |
Delete DB 73 in the PLC and restart |
400174 |
Delete DB 74 in the PLC and restart |
400250 |
NCK sign-of-life monitoring |
400251 |
NCK has not started up |
400252 |
Sign-of-life monitoring |
400260 |
Failure of machine control panel 1 |
400261 |
Failure of machine control panel 2 |
400262 |
Failure of manual operating device |
400604 |
Set change with M06 in the machine data |
400902 |
Impermissible channel no. parameter in FC 9 |
401502 |
Impermissible axis no. parameter in FC 15 |
401602 |
Impermissible axis no. parameter in FC 16 |
401702 |
Impermissible spindle IF no. parameter in FC 17 |
401805 |
Impermissible axis no. parameter in FC 18 |
401901 |
Impermissible BAG no. parameter in FC 19 |
401902 |
Impermissible channel no. parameter in FC 19 |
402501 |
Impermissible BAG no. parameter in FC 25 |
402502 |
Impermissible channel no. parameter in FC 25 |
410150 |
Area in M group decoder list is too large |
810001 |
Error OB_event |
810002 |
Synchronous error |
810003 |
Asychronous error |
810004 |
Stop/Interrupt event |
810005 |
Order form execution event |
810006 |
Error communication event |
810007 |
Error H/F system event |
810008 |
Error diagnostics data from modules |
810009 |
User-diagnostics event |